AMI 186 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 65

background image

25

Operation

Normal Operation

4. Configure the A SETPOINT and the B SETPOINT

To adjust the A and B setpoints which specify the upper and lower limits for the liquid
level control band, place the control mode rotary switch in the A SETPOINT position
or the B SETPOINT position, respectively. Use the RAISE/LOWER toggle switch to
adjust the respective setpoint in the same manner as described for the LENGTH
adjustment in step 2. The A and B setpoint adjustments are compatible with all three
units modes.

a. When the measured liquid level reaches or exceeds the A setpoint, the A

LEVEL LED on the front panel is energized. When the level falls below
the A setpoint, the LED is extinguished.

b. When the measured liquid level falls below the B setpoint, the B LEVEL

LED on the front panel is energized. When the level reaches or exceeds
the B setpoint, the LED is extinguished.

c. In addition to the LED functions, the controller output receptacle may be

energized and de-energized as discussed in step 5 below.

Note

The A setpoint must always be above the B setpoint. The firmware does not
allow these setpoints to be reversed. Both setpoints may be set from 0% to
100% of the LENGTH setting as long as A > B.

5. Select the operational mode of the controller output receptacle

The operation of the CONTROLLER OUTPUT receptacle of the instrument is
controlled by the fill toggle switch. Operation of the fill toggle switch is as follows:

a.

OFF:

With the power on and the fill switch in the OFF position, the

instrument serves only as a level monitor, giving a level reading on the
digital display and providing data via any analog or communication
options installed. All four setpoint LEDs (and associated J2 connector
relay contacts) operate normally, however, the controller output receptacle
on the rear panel will

always

be de-energized.

b.

ON:

With the fill switch in the ON position, the rear panel

CONTROLLER OUTPUT receptacle will become energized, thereby
initiating flow if the solenoid-operated fill valve is properly connected.
The FILL LED on the front panel will light indicating the presence of
power at the controller output receptacle.

The operator is solely

responsible for terminating the fill flow.

c.

AUTO:

With the fill switch in the AUTO position, the instrument is

capable of automatically initiating and terminating liquid fill via the
control valve, thereby maintaining the level between the selected A and B
setpoints. If the liquid level falls below the B setpoint, the rear panel

«
...
24
25
26
27
28
...
»

Содержание 186


































































Отзывы:

Нет отзывов

Похожие инструкции для 186

Бренд: GE Страницы: 2

Бренд: XOXO Modular Страницы: 13

Бренд: Saitek Страницы: 13

Бренд: Balboa Water Group Страницы: 28

Бренд: UE Страницы: 4

Бренд: Faber Страницы: 8

SmartSwitch 6000

Бренд: Cabletron Systems Страницы: 76

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 12

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 8

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 14

Бренд: FAAC Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды