manualshive.com logo in svg

AMI 186, Инструкции по установке, эксплуатации и обслуживанию

Поделиться
Скачать
AMI 186 Скачать руководство пользователя страница 18

17

Calibration

Closed Dewar Calibration

If minimum and maximum liquid level indication is available via some other means 
(e.g. flow calculation, visual determination, point sensors, etc.), then the presetting of 
the instrument is not necessary.

Presetting the MAX/MIN calibration points

The following procedure should be performed before installation of the sensor in the 
target cryo-vessel.

1. Connect the extension and oscillator cables to the J5 coaxial connector on the 

rear panel of the instrument (see page 5 for a system diagram). 

Do not connect 

the sensor.

 Energize the instrument. Press the MIN push-button through the 

small hole provided on the instrument front panel. When the calibration point 
has been accepted, the display will show "bbb.b" and the push-button can then 
be released.

2. Connect the sensor to the oscillator cable (which is still connected to the 

instrument via the extension cable). Press the MAX push-button through the 
small hole provided on the instrument front panel. When the calibration point 
has been accepted, the display will show "bbb.b" and the push-button can then 
be released.

3. Calculate the factor 

C

adj

 

using the following equation:

where 

L

total

 is the total sensor length in inches, 

L

active

 is the active sensor length 

in inches, and 

e

 is the dielectric constant of the target liquid. 

4. Enter 

C

adj

 into the instrument by placing the front panel control mode rotary 

switch in the SILENCE position. By using the RAISE/LOWER toggle switch 
and holding it in the up or down position, adjust the displayed value up or 
down. The display will move slowly at first and then faster. Once near the 
desired value, simply release the switch momentarily and then resume 
changing the factor at the slower speed. Once the desired number has been 
reached, release the toggle switch.

5. Once the value for 

C

adj

 has been entered, momentarily press the CAL push-

button labeled as "~" (the tilde character) through the small hole provided in 
the instrument front panel. When the value has been accepted, the display will 
show "ddd.d" and the button can then be released.

6. With the sensor connected, again press the MIN push-button through the 

small hole provided on the instrument front panel. When the calibration point 
has been accepted, the display will show "bbb.b" and the push-button can then 
be released. The presetting procedure is complete. Proceed to the closed 
dewar calibration procedure.

C

adj

120 1

2.1

L

active

5.2

L

total

------------------------

+

e

1

–

0.454

-------------

=

Содержание 186


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды