manualshive.com logo in svg

AMI 186, Инструкции по установке, эксплуатации и обслуживанию

Поделиться
Скачать
AMI 186 Скачать руководство пользователя страница 24

23

3 Operation

The Model 186 and sensor were functionally tested and calibrated at the factory. The 
calibration sticker located on the bottom of the instrument shows the calibration 
length, calibration liquid, and whether an approximate calibration method was utilized 
at the factory. In the event that the calibration is incorrect for the application, the 
instrument will need to be recalibrated by the user with a specific sensor and liquid. 
Refer to the 

Calibration

 section for the specific procedures.

1. Energize the instrument

After completion of the 

Installation

 procedures, energize the instrument by placing 

the power toggle switch in the POWER position. The LED display will indicate the 
liquid level and the yellow ACTIVITY LED will begin blinking.

Note

The ACTIVITY LED provides visual indication that the microprocessor is 
making sensor readings. If a fault should develop which prohibits the 
microprocessor from operating correctly (such as a break in cabling) the 
LED will not blink or blink slowly, and the display will continuously show 
100%.

The instrument is normally calibrated at the factory for the specific sensor supplied 
with the unit for use in a target liquid. If the need arises for recalibration, see the 

Calibration

 section.

2. Configure the active length setting

After calibration, the instrument 

must

 be configured for the active length of the sensor 

in order to scale the measurement to meaningful units of length for display. For a 
standard calibration, the value of the active length is the sensor length between the 
bottom hole to 1 inch below the top hole of the sensor assembly. If the user performed 
a calibration, then the physical distance between the locations of the MIN and MAX 
calibration points on the sensor is the active length.

The instrument allows the user to display the liquid level in units of length (inches or 
centimeters) in addition to a percentage. The instrument was shipped with the length 
value set to the active sensor length if a sensor was purchased with the instrument.

To 

view

 the present length setting, place the units mode toggle switch in either the 

INCH or CM position. Place the control mode rotary switch on the front panel to the 
LENGTH position. Push and 

release

 the RAISE/LOWER toggle switch either up or 

down. The display will momentarily show the current length setting. 

Содержание 186


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды