AMF S-4001 ISBH+I SM 30 Скачать руководство пользователя страница 37

Страница: 37 / 90

S-4001 ISBH+I SM 30°

1-25

Released: 09/2017
E-mail: [email protected]; webside: amfreece.com
Phone: +420 582 309 146; Fax: +420 582 360 606

D - MACHINE CONTROLS

6. TESTS

Warning!

Tests can be performed only by skilled service technicians.

Press button key to activate the draw-off.

The valve J1 is tested by this parameter.

When the button key is pressed, the clamp feet

are closed.The valve J2 is tested by this parameter.

Press button key to activate the thread trimming.

The valve J3 is tested by this parameter.

Press button key to close the indexer clamp feet.

The valve J10 is tested by this parameter.

Press button key to activate the thread pick.

The valve J11 is tested by this parameter.

J10

J11

J10

J11

The end position sensor BQ1. Activate the sensor using a metal

tool - icon starts lighting.

If the air pressure is less than 0,5 MPa the button is underlighted.

After pressing button key EMERGENCY STOP the icon

lights.

If the servodriver is in operation the icon lights.

When the foot pedal is pressed to its first position the button SB4

is underlighted.

SB4

SB4

When the foot pedal is pressed to its second position the button SB5

is underlighted.

SB5

SB5

SQ2

BQ3

SQ2

The end position axis X. Activate the sensor using a metal

tool - icon starts lighting.

The end position axis Y. Activate the sensor using a metal

tool - icon starts lighting.

BQ3

BQ2

Содержание S-4001 ISBH+I SM 30



























































































Результаты поиска

Содержание S-4001 ISBH+I SM 30

Отзывы:

AMF S-4001 ISBH+I SM 30, Руководство по эксплуатации и ремонту, Страница: 37 / 90

Результаты поиска

Содержание S-4001 ISBH+I SM 30

Отзывы: