AMF S-4001 ISBH+I SM 30 Скачать руководство пользователя страница 19

Страница: 19 / 90

S-4001 ISBH+I SM 30°

1-7

Released: 09/2017

E-mail: [email protected]; webside: amfreece.com

Phone: +420 582 309 146; Fax: +420 582 360 606

A - INTRODUCTION

6. SPECIAL ACCESSORIES

- machine device, which is not included in the standard equipment of the machine and a customer can order it

Sewing cam

• it is possible to sew a different buttonhole shape

than standard

buttonhole

•

a cutomer can order it

part number 24.3079.0.000

part number 24.3080.0.000

•

to change a cam - see section E20

Needles 750 SC 80/12, 70/10

•

the manufacturer recommends to use these needles when sewing the thin

materials

•

part number 02.0750.2.100 (80/12), 02.0750.2.109 (70/10)

Connector

•

order it if the connecting tube has the inner diameter

8 mm. The connector Ø 10 is supplied with the

machine.

•

part number is 12.0008.3.607

Pneumatic Adapater

•

order it if using 1/8“ NPT

•

part number 12.0008.3.081

Hand valve

•

to dissipate any air from the machine, order it (air circuit is bled). It is necessary to order the connectors (see

below) to the hand valve for connection to the air tubes.

•

part number 12.0008.3.463

Connectors

12.0008.3.464 Ø 8

for connection to the tube with inner Ø 8 mm

12.0008.3.466 Ø 10

for connection to the tube with inner Ø 10 mm

12.0008.3.467 Ø 12

for connection to the tube with inner Ø 12 mm*

12.0008.3.465 Ø 16

for connection to the tube with inner Ø 16 mm*

* To connect the tube with inner Ø 12 and Ø 16,

it is also necessary to order Ø 10

Laser light kit

03.5519.0.022

Содержание S-4001 ISBH+I SM 30



























































































Результаты поиска

Содержание S-4001 ISBH+I SM 30

Отзывы:

AMF S-4001 ISBH+I SM 30, Руководство по эксплуатации и ремонту, Страница: 19 / 90

Результаты поиска

Содержание S-4001 ISBH+I SM 30

Отзывы: