AMF S-4000 BH Omron Скачать руководство пользователя страница 73

Страница: 73 / 78

S-4000 BH Omron

2-3

TROUBLESHOOTING

e-mail. [email protected]; [email protected]; website: www.amfreece.com
Phone: +420 582 309 286; Fax: +420 582 360 606

Released 05/2010

SYMPTOM

POSSIBLE CAUSE

PROBABLE SOLUTION

Stitch skip at the beginning
of sewing

Stitch skip during sewing

Needle, looper, throat plate
damaged

Needle thread end is too short

Incorrectly adjusted needle bar
height

Incorrectly adjusted clearance
between needle and throat
plate

Incorrect loopers timing

Incorrectly adjusted clamp feet
pressure

Incorrectly adjusted the home
position of the clamp plate

Needle, looper, throat plate
damaged

Incorrectly adjusted needle bar
height

Incorrectly adjusted clearance
between needle and throat
plate

Incorrect loopers timing

Incorrect thread tension
adjustment

Incorrect threading

Thread loops are too small

Incorrectly adjusted clamp feet
pressure

The clamp feet are adjusted
too far from the sewing

Change damaged parts

See section E13, point 2

See section E4

See section E5

See section E9

See section E 17, point 3

See section E11

Change damaged parts

See section E4

See section E5

See section E9

Adjust the tension correctly

See section C3

See section E13 point 3

See section E17 point 3

See section E17 point 2

Содержание S-4000 BH Omron















































































Результаты поиска

Содержание S-4000 BH Omron

Отзывы:

AMF S-4000 BH Omron, Руководство по эксплуатации и ремонту, Страница: 73 / 78

Результаты поиска

Содержание S-4000 BH Omron

Отзывы: