manualshive.com logo in svg

AMF S-4000 BH Omron, Руководство по эксплуатации и ремонту, Страница: 26 / 78

Поделиться
Скачать
AMF S-4000 BH Omron Скачать руководство пользователя страница 26

S-4000 BH Omron

1-20

Released 05/2010

e-mail: [email protected]; [email protected]; website: www.amfreece.com

Phone: +420 582 309 286; Fax: +420 582 360 606

D - MACHINE CONTROLS

9.

It is possible to sew two styles of buttonhole alignment on the machine.

a)

S e w in g   t h e   l e n g t h w is e   b u t t o n h o l e s

 

●

remove the parts 22.0011.0.000 

➊

, 22.0012.0.000 

➋

, 08.6010.5.008 

➏

,

08.6400.4.004 

➐

 from accessories and install them to the machine.

●

to adjust the clearance 

X

 between the center of a buttonhole and the material edge, loosen

the screw 

➐

 and move the stop 

➋

 as needed. Tighten the screw 

➐

. It is possible to adjust

the stop in range 13 - 39 mm.

Note:

 If the stop is set to 13 mm and the bite size is increased, the left clamp foot  

➑

 must

not hit the stop 

➋

.

b)

S e w in g   t h e   c r o s s w is e   b u t t o n h o l e s

 

●

remove the parts 22.0044.0.000 

➒

, 22.0010.0.000 

➓

, 08.6010.5.008 

➏

,

08.6400.4.004 

➐

 from accessories and install them to the machine.

●

to adjust the clearance 

Y

 between the buttonhole edge and the material edge, loosen the

screw 

➐

 and move the stop 

➋

 as needed. Tighten the screw 

➐

. It is possible to adjust the

stop in range 10 - 60 mm.

Note:

 It the stop is set to 10 mm and the length of a buttonhole is increased, it is necessary

to move the stop towards the machine head!

➊

,

➏

➐

➋

➑

➐

,

➒

➏

➓

Содержание S-4000 BH Omron















































































Отзывы:

Нет отзывов