AMF S-4000 BH Omron Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 78

AMF S-4000 BH Omron Скачать руководство пользователя страница 40

S-4000 BH Omron

1-34

Released 05/2010

e-mail: [email protected]; [email protected]; website: www.amfreece.com

Phone: +420 582 309 286; Fax: +420 582 360 606

Ó

Ó

Ó

Ó

Ó

E - MACHINE ADJUSTMENTS

6 . F E E D I N G

1.

Tilt the sewing head onto the rest pin.

2.

Bevel Gear Adjustments
Manually turn the handwheel counter clockwise until the
drive spring in the main cam engages with a indent (first
row of stitches). The feeding lever is on the highest point of
the feeding cam. Remove the bevel gear cover and loosen

the screws

➊

,

➋

on the horizontal bevel gears and screw

➌

on the stop.

3.

Loosen two adjusting screws

➍

in the right collar

➎

.

Adjust the dimension 11mm from the end of the feed

shaft

➏

to the collar

➐

by pressing the feed shaft

➏

against

the right collar

➎

. Tighten the adjusting screws

➍

in the

right collar

➎

. The tension of the left collar on the shaft is

set.

4.

Engage the right bevel gear

➑

with the vertical bevel

gear

➒

and lock its position by the set screws

➊

.

5.

Manually turn the handwheel counterclockwise until the
drive spring engages with right shifter block pocket (the
second row of stitches). The feeding lever is on the lowest

point of the feeding cam. Slide the right gear

➓

into

engagement with the vertical gear

➒

. Tighten the set

screws

➋

securely. Move the crank drive to the left bevel

gear

➓

and lock it by screw

➌

.

The bevel gear adjustment is done. By manually turning the
handwheel finish the sewing cycle and bring the machine to the
home position. Reinstall the bevel gear cover.

6.

Clamp plate movement occurs only when the needlepoint
has risen above the work piece and must be completed
before the needle descends into the work.

7.

For adjustment use a piece of paper to see the needle
punctures.

If feeding occurs while the needle is in the work, engage
the drive spring into a indent.

Loosen the screws

on the feed cam and adjust its

position as needed so that all feed motion occurs with the
needle out of the work. Retighten the feed cam set screws.

Ì

Ì

Ì

Ì

Ì

Ë

Ë

Ë

Ë

Ë

Í

Í

Í

Í

Í

Î

Î

Î

Î

Î

Ï

Ï

Ï

Ï

Ï

Ð

Ð

Ð

Ð

Ð

11 mm

Ê

Ê

Ê

Ê

Ê

Ñ

Ñ

Ñ

Ñ

Ñ

Ò

Ò

Ò

Ò

Ò

Ò

Ò

Ò

Ò

Ò

Ë

Ë

Ë

Ë

Ë

«
...
38
39
40
41
42
...
»

Содержание S-4000 BH Omron















































































Отзывы:

Нет отзывов