AMF S-4000 BH Omron Скачать руководство пользователя страница 72

Страница: 72 / 78

S-4000 BH Omron

e-mail: [email protected]; [email protected]; website: www.amfreece.com

Phone: +420 582 309 286; Fax: +420 582 360 606

Released 05/2010

2-2

TROUBLESHOOTING

SYMPTOM

POSSIBLE CAUSE

PROBABLE SOLUTION

Thread breakage

Machine fails to sew

Machine sews in one spot

Needle, looper, throat plate
damaged

Incorrect needle and sewing
mechanism adjustment

Thread tension is too tight

Incorrect threading

Thread guides polished
incorrectly

Poor thread quality

Thread is too heavy for
selected needle and throat
plate

Needle, looper, throat plate
damaged

Incorrectly adjusted needle bar
height

Incorrectly adjusted clearance
between needle and throat
plate

Incorrect loopers timing

Incorrectly adjusted the home
position of the clamp plate

Change damaged parts

Check the adjustment of the
mechanisms

Adjust correct tension

See section C3 for checking.

Polish

Replace thread

Use recommended thread sizes -
see section A4

Change damaged parts

See section E4 for checking

See section E5 for checking

See section E9 for checking

Adjust the stop - see section E11

1 . MECHANICAL FAULTS

Содержание S-4000 BH Omron















































































Результаты поиска

Содержание S-4000 BH Omron

Отзывы:

AMF S-4000 BH Omron, Руководство по эксплуатации и ремонту, Страница: 72 / 78

Результаты поиска

Содержание S-4000 BH Omron

Отзывы: