AMF S-4000 BH Omron Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 78

AMF S-4000 BH Omron Скачать руководство пользователя страница 23

S-4000 BH Omron

1-17

Released 05/2010

e-mail: [email protected]; [email protected]; website: www.amfreece.com
Phone: +420 582 309 286; Fax: +420 582 360 606

C - PROPER APPLICATION

2 . N E E D L E I N S TA L L AT I O N

WARNING!

Before performing this adjustment, switch the main machine power off to prevent accidental

starting of the machine. Disconnect the air supply and dissipate any stored energy.
Use needles ordering number 02.0750.2.110 (750SC 90/14) only - see accessories.
It is also possible to use needles ordering number 02.0750.2.100 (750 SC 80/12) for sewing the thin
materials - these needles are not included in the standard machine equipment.

1.

Using the screwdriver push the latch

➊

and open the needle bar cover

➋

.

Note:

The accessories contain the lever

➎

(ordering number 22.0213.0.000) and screw (ordering

number 08.6000.4.005) with washer (08.6850.4.000)

➏

, which is possible to fit to the latch. It allows

opening of the cover without using the tool.

2.

Loosen the screw

➌

and remove the needle.

3.

Insert the new needle so that the long thread

groove

➍

is in the rear and the spot for the

clamping screw

➌

is in line. Do not install a

bent or broken needle. Roll the needle on a flat
surface to check for straightness.

4.

Tighten the screw

➌

well.

Ê

Ê

Ê

Ê

Ê

Ë

Ë

Ë

Ë

Ë

«
...
21
22
23
24
25
...
»

Содержание S-4000 BH Omron















































































Отзывы:

Нет отзывов