manualshive.com logo in svg

AMF S-4000 BH Omron, Руководство по эксплуатации и ремонту, Страница: 31 / 78

Поделиться
Скачать
AMF S-4000 BH Omron Скачать руководство пользователя страница 31

S-4000 BH Omron

1-25

Released 05/2010

e-mail: [email protected]; [email protected]; website: www.amfreece.com
Phone: +420 582 309 286; Fax: +420 582 360 606

D - MACHINE CONTROLS

5 .   T E S T S

WARNING! ONLY PROFESSIONAL SERVICE TECHNICIANS SHOULD PERFORM THESE TESTS!

NOTICE! BEFORE PERFORMING ANY TESTS DISMOUNT THE CUTTING KNIFE AND THE

NEEDLE!

The main screen appears on the display. Press 

,   

appears on the display.

To enter the tests menu, press 

 key. The following screen appears on the display

Intput tests

Off

Low air pres

. To scroll this menu down, press 

 key, to scroll this menu up, press 

 key.

INPUTS TESTS

1. 

Intput tests

Off

Low air press

 -

If the air pressure falls below 0,5 MPa, 

 appears

on the display.
Sensor BQ2 is tested by this parameter.

2. 

Home sensor
Voltage Rly

Off

Off

 -

the end position sensor. Activate the sensor using a metal tool.

Home sensor
Vo l t a g e R l y

O n

O f f

 appears on the display.

Switch BQ1 is tested by this parameter.

3. 

 -

This input signifies when the overvoltage relay is installed. If the voltage

drops below185 V, 

Home sensor
Vo l t a g e R l y

O f f

O n

 appears on the display. Relay

VC1 tested by this parameter.

4. 

-

After pressing the pedal to the first position, 

Pedal 1 step
Pedal 2 step

Off

On

appears on the display. Switch SB4 is tested by this parameter.

5. 

Pedal 1 step
Pedal 2 step

Off

Off

-

After pressing the pedal to the second position, 

Pedal 1 step
Pedal 2 step

On

On

appears on the display. Switch SB5 is tested by this parameter.

6.

Em stop
Clamp button

On

Off

-

After pressing the button 

 this appears on the display:

Em stop
Clamp Button

Off

Off

. After releasing the button

Em stop
Clamp button

On

Off

 appears. Switch SA1 is tested by this parameter.

Display

Содержание S-4000 BH Omron















































































Отзывы:

Нет отзывов