American Dryer Corp. ML-122D Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 55

background image

For replacement parts, contact the reseller from which the dryer

was purchased or

American Dryer Corporation

88 Currant Road

Fall River MA 02720-4781

Telephone: (508) 678-9000 / Fax: (508) 678-9447

E-mail: [email protected]

www.amdry.com

WARNING: For your safety the
information in this manual must be
followed to minimize the risk of fire or
explosion or to prevent property damage,
personal injury or death.

Do not store or use gasoline or other flammable
vapor and liquids in the vicinity of this or any
other appliance.

WHAT DO YOU DO IF YOU SMELL GAS

* Do not try to light any appliance.
* Do not touch any electrical switch; do not use

any phone in your building.

* Clear the room, building or area of all

occupants.

* Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's
instructions.

* If you cannot reach your gas supplier, call the

fire department.

Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.

AVERTISSEMENT: Assurez-vous de bien
suivre les instructions données dans cette
notice pour réduire au minimum le risque
d’incendie ou d’explosion ou pour éviter tout
dommage matériel, toute blessure ou la mort.

Ne pas entreposer ni utiliser d’essence ni
d’autres vapeurs ou liquides inflammables dans
le voisinage de cet appareil ou de tout autre
appareil.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR
DE GAZ:

* Ne pas tenter d’allumer d’appareil.
* Ne touchez à aucun interrupteur. Ne pas

vous servir des téléphones se trouvant dans
le bâtiment où vous vous trouvez.

* Évacuez la pièce, le bâtiment ou la zone.
* Appelez immédiatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions
du fournisseur.

* Si vous ne pouvez rejoindre le fournisseur

de gaz, appelez le service des incendies.

L’installation et l’entretien doivent être assurés
par un installateur ou un service d’entretien
qualifié ou par le fournisseur de gaz.

020900RF/pb

ADC

Part No. 113126

ML-122D

(Gas & Steam)

Installation Manual

1
2
3
...
»

Содержание ML-122D
























































Отзывы:

Нет отзывов

Похожие инструкции для ML-122D

Spacemaker DSKS333EC

Бренд: GE Страницы: 3

Бренд: GE Страницы: 4

Бренд: Aurora Страницы: 8

Бренд: Atag Страницы: 74

Бренд: Maytag Страницы: 51

Бренд: san ignacio Страницы: 27

Бренд: MPM Страницы: 36

Бренд: SMC Networks Страницы: 4

Бренд: Braun Страницы: 4

Бренд: Van Air Systems Страницы: 12

Бренд: Häfele Страницы: 17

Бренд: Magic Chef Страницы: 42

Бренд: EXALTA Страницы: 52

Profile UPVH890

Бренд: GE Страницы: 152

Profile Harmony PTDN805EM

Бренд: GE Страницы: 76

Бренд: GE Страницы: 60

Бренд: GE Страницы: 40

Бренд: Haier Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды