American Dryer Corp. ADG-530D II Скачать руководство пользователя | Manualshive

Страница: 1 / 57

background image

ADC

Part No. 113116

101399JEV/abe

ADG-530D II/WDA-530D II

Microprocessor Controls

Gas (Direct Spark Ignition)

Installation Manual

WARNING: For your safety the information in
this manual must be followed to minimize the
risk of fire or explosion or to prevent property
damage, personal injury or death.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any
other appliance.

— WHAT TO DO IF YOU SMELL GAS:

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not
use any phone in your building.

•

Clear the room, building or area of all
occupants.

•

Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.

•

If you cannot reach your gas supplier, call
the fire department.

— Installation and service must be performed by a

qualified installer, service agency or the gas
supplier.

AVERTISSEMENT: Assurez-vous de bien
suivre les instructions données dans cette notice
pour réduire au minimum le risque d’incendie
ou d’explosion ou pour éviter tout dommage
matériel, toute blessure ou la mort.

— Ne pas entreposer ni utiliser d’essence ni

d’autres vapeurs ou liquides inflammables à
proximité de cet appareil ou de tout autre
appareil.

— QUE FAIRE SI VOUS SENTEZ UNE ODEUR

DE GAZ:

•

Ne pas tenter d’allumer d’appareils.

•

Ne touchez à aucun interrupteur. Ne pas
vous servir des téléphones se trouvant dans
le bâtiment.

•

Évacuez la pièce, le bâtiment ou la zone.

•

Appelez immédiatement votre fournisseur
de gaz depuis un voisin. Suivez les
instructions du fournisseur.

•

Si vous ne pouvez rejoindre le fournisseur
de gaz, appelez le service des incendies.

— L’installation et l’entretien doivent être assurés par

un installateur ou un service d’entretien qualifié
ou par le fournisseur de gaz.

For replacement parts, contact the reseller from which the dryer

was purchased or

American Dryer Corporation

88 Currant Road

Fall River MA 02720-4781 USA

Telephone: (508) 678-9000 / Fax: (508) 678-9447

e-mail: [email protected]

www.amdry.com

1
2
3
...
»

Содержание ADG-530D II


























































Отзывы:

Нет отзывов

Похожие инструкции для ADG-530D II

Бренд: Cajun Страницы: 12

Бренд: Maytag Страницы: 7

Бренд: UFESA Страницы: 42

Бренд: GE Страницы: 40

Бренд: Far West Страницы: 41

Perfoma PYE4500

Бренд: Maytag Страницы: 9

SmartFry XL ADF-212

Бренд: Aroma Страницы: 22

Pneudri Maxi MX102c

Бренд: Domnick Hunter Страницы: 14

Бренд: Asko Страницы: 24

Бренд: Trisa electronics Страницы: 25

Бренд: Daewoo Страницы: 31

Бренд: Aurora Страницы: 8

Бренд: Blue Seal Страницы: 21

Бренд: Haier Страницы: 8

Бренд: Haier Страницы: 23

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 31

Бренд: Haier Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды