Amazone ZA-M Profis Hydro Скачать руководство пользователя страница 88

Страница: 88 / 104

Cleaning, maintenance and repairs

ZA-M BAG0040.8 09.15

Cleaning, maintenance and repairs

WARNING

Risk of contusions, shearing, cutting, catching, entanglement
drawing in and knocks through

•

Unintentional falling of the machine raised using the trac-
tor's three-point linkage.

•

Unintentional falling of raised, unsecured machine parts.

•

Unintentional start-up and rolling of the tractor-machine
combination.

Secure the tractor and machine against unintentional start-up and
rolling, before carrying out cleaning, maintenance or repair work on
the machine when coupling or decoupling the machine. See also
page 57.

WARNING

Risk of contusions, cutting, catching, drawing in and knocks
through unprotected danger points!

•

Mount protective equipment, which you removed when cleaning,
maintaining and repairing the machine.

•

Replace defective protective equipment with new equipment.

WARNING

Danger from crushing, shearing and/or impact through uninten-
tional closing of the open, unsecured guard and function screen!

Secure the open guard and function screen so that it cannot move
accidentally before carrying out work in this area. See page 39.

Содержание ZA-M Profis Hydro









































































































Результаты поиска

Содержание ZA-M Profis Hydro

Отзывы:

Бренды по названию

Популярные бренды

Amazone ZA-M Profis Hydro, Руководство по эксплуатации

Результаты поиска

Содержание ZA-M Profis Hydro

Отзывы:

Бренды по названию

Популярные бренды