Amazone ZA-M Profis Hydro Скачать руководство пользователя страница 85

Страница: 85 / 104

Faults

ZA-M BAG0040.8 09.15

Faults

WARNING

Risk of contusions, shearing, cutting, catching, entanglement
drawing in and knocks through

•

Unintentional falling of the machine raised using the trac-
tor's three-point linkage.

•

Unintentional falling of raised, unsecured machine parts.

•

Unintentional start-up and rolling of the tractor-machine
combination.

Secure the tractor and the machine against unintentional start-up and
rolling, before eliminating faults on the machine. See page 57.

Wait for the machine to stop before entering the machine danger
area.

11.1

Eliminating agitator malfunctions

WARNING

Danger from crushing, shearing and/or impact through uninten-
tional closing of the open, unsecured guard and function screen!

Secure the open guard and function screen so that it cannot move
accidentally before carrying out work in this area. See page 39.

11.2

Faults in electronics

If faults develop in the Control terminal or the electric setting motors
that cannot be eliminated immediately, it is still possible to continue
working (see the corresponding operating manual).

Содержание ZA-M Profis Hydro









































































































Результаты поиска

Содержание ZA-M Profis Hydro

Отзывы:

Бренды по названию

Популярные бренды

Amazone ZA-M Profis Hydro, Руководство по эксплуатации

Результаты поиска

Содержание ZA-M Profis Hydro

Отзывы:

Бренды по названию

Популярные бренды