manualshive.com logo in svg

Amazone ZA-M Profis Hydro, Руководство по эксплуатации

Поделиться
Скачать
Amazone ZA-M Profis Hydro Скачать руководство пользователя страница 63

 

 

 

 

Coupling and uncoupling the machine 

 

ZA-M  BAG0040.8  09.15

 

63 

 

7.2 

Uncoupling the machine 

 

WARNING 

Danger from crushing and / or impacts 

•

 

due to insufficient stability and tilting of the uncoupled ma-
chine on uneven, soft ground! 

•

 

due to unintentional rolling of the machine parked on a 
transportation device! 

•

 

Always place the uncoupled machine with empty hopper on a 
horizontal storage space with a solid base. 

•

 

Secure the machine against unintentional rolling when you park 
the machine on a transportation device. Here, see the chapter 
"Transportation and parking device", page 50. 

 

 

CAUTION 

Risk of tipping 

When setting down the fertilizer spreader, only a small residual 
amount may be found in the hopper. 

 

 

When uncoupling the machine, there must always be enough space 
in front of the machine, so that you can align the tractor with the ma-
chine if necessary. 

 
 

  1.  Always place the machine with empty hopper on a horizontal 

storage space with a solid base. 

  2.  Always check for visible damage when uncoupling the machine. 

See the chapter "Obligation of operator" on page 9. 

  3.  Uncouple the machine from the tractor as follows: 

 3.1  Relieve the load from the top link. 
 3.2  Unlock and uncouple the top link hooks from the tractor 

seat. 

 3.3  Relieve the load from the lower link. 
 3.4  Unlock and uncouple the lower link hooks from the tractor 

seat. 

 3.5  Draw the tractor approximately 25 cm forwards. 

 

→

  The resulting free space between the tractor and the ma-

chine provides better access to the supply lines when dis-
connecting them. 

 3.6  Secure the tractor against unintentional starting and rolling 

away, see the chapter "Securing the tractor against unin-
tentional starting and rolling away", from page 57. 

 3.7  Secure the machine to prevent it from accidentally rolling 

away if the machine is equipped with a transport fixture – 
see "Transport and parking device" chapter on page 50.  

 3.8  Uncouple the hydraulic hose lines, see the chapter "Un-

coupling the hydraulic hose lines", from page 46. 

 3.9  Uncouple the lighting system, see the chapter "Transporta-

tion equipment", page 33. 

3.10 Couple the Control terminal, refer to separate operating 

manual for AMATRON 3. 

 

Содержание ZA-M Profis Hydro









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды