manualshive.com logo in svg

Amazone ZA-M Profis Hydro, Руководство по эксплуатации

Поделиться
Скачать
Amazone ZA-M Profis Hydro Скачать руководство пользователя страница 64

 

 

 

Adjustments 

 

 

64  

ZA-M  BAG0040.8  09.15 

 

8 

Adjustments 

 

When performing any adjustment work on the machine, observe the 
information in the following chapters 

•

 

"Warning pictograms and other labels on the machine" from 
page 16 and 

•

 

"Safety information for the operator" from page 24. 

Observing this information is important for your safety. 

 

 

WARNING 

Danger of, shearing, cutting, entrapment, entanglement, being 
drawn in, caught or struck during all adjustment work on the 
machine 

•

 

due to unintentional contact with moving operating ele-
ments (spreading vanes of rotating spreading discs). 

•

 

due to tractor and connected machine unintentionally start-
ing up or rolling away. 

•

 

Secure the tractor and the machine against unintentional start-
up and rolling, before adjusting the machine. See page 57. 

•

 

Only touch moving operating elements (rotating spreading discs) 
when they have come to a complete standstill. 

 

 

WARNING 

Risk of contusions, catching and knocks during all adjustment 
work on the machine due to unintentional lowering of the cou-
pled and raised machine. 

Secure the tractor cabin against entry of other persons to prevent 
unintentional actuation of the tractor's hydraulic system. 

 
 

 

Please note that the individual spreading properties of the spread 
material have a significant influence on the lateral distribution and 
spread rate. For this reason, the listed setting values should only be 
considered as a reference. 

The spreading properties depend on the following factors: 

•

 

The fluctuations in the physical data (specific weight, grain 

size, frictional resistance, cw value, etc.) within the same type 
and brand 

•

 

The different properties of the spread material due to weather 

factors and/or storage conditions. 

As a result of this, we cannot guarantee that your spreading material, 
even with the same name and from the same manufacturer, has the 
same spreading properties as the listed spreading material. The 
specified setting recommendations for the lateral distribution are 
based exclusively on the weight distribution and not on the nutrient 
distribution (this applies particularly for mixed fertilisers) or the active 
substance distribution (e.g., for slug pellets or lime). Claims for dam-
ages not caused by the centrifugal spreader itself are excluded. 

 

Содержание ZA-M Profis Hydro









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды