Amazone ZA-M Profis Hydro Скачать руководство пользователя страница 44

Страница: 44 / 104

Structure and function

ZA-M BAG0040.8 09.15

5.7

Hydraulic connections

•

All hydraulic hose lines are equipped with grips.

Coloured markings with a code number or code letter have been

applied to the gripping sections in order to assign the respective
hydraulic function to the pressure line of a tractor control unit!

Films are stuck on the implement for the markings that illustrate

the respective hydraulic function.

•

The tractor control unit must be used in different types of activa-
tion, depending on the hydraulic function.

Latched, for a permanent oil circulation

Tentative, activate until the action is executed

Float position, free oil flow in the control unit

Marking

Function

Tractor control unit

Red

Permanent oil circulation

Red

Pressure-free return flow

Red

Load sensing control line

Maximum permissible pressure in oil return: 8 bar

Therefore do not connect the oil return to the tractor control unit, but
to a pressure-free oil return flow with a large plug coupling.

WARNING

For the oil return, use only DN16 lines and select short return
paths.

Pressurise the hydraulic system only when the free return has
been correctly coupled.

Install the coupling union (supplied) on the pressure-free oil return
flow.

Содержание ZA-M Profis Hydro









































































































Результаты поиска

Содержание ZA-M Profis Hydro

Отзывы:

Бренды по названию

Популярные бренды

Amazone ZA-M Profis Hydro, Руководство по эксплуатации

Результаты поиска

Содержание ZA-M Profis Hydro

Отзывы:

Бренды по названию

Популярные бренды