Amazone ZA-M Profis Hydro Скачать руководство пользователя страница 19

Страница: 19 / 104

General safety instructions

ZA-M BAG0040.8 09.15

Order number and explanation

Warning pictograms

MD 082

Danger of persons falling from tread surfaces
and platforms when riding on the machine or
when climbing on powered machines.

This danger can cause extremely serious and
potentially fatal injuries.

It is forbidden to ride on the machine and/or
climb on the machine when it is in operation.
This also applies to machines with tread surfaces
or platforms.

Make sure that nobody is riding on the machine.

MD 083

Danger of your arm or upper torso being
drawn in or caught by power driven, unpro-
tected machine elements!

This danger can cause extremely serious injuries
to the arm or upper torso.

Never open or remove protective devices from
driven machinery

•

as long as the tractor engine is running with
the PTO shaft connected / hydraulic drive
engaged or

•

as long as the tractor engine can be unin-
tentionally started with the PTO shaft con-
nected / hydraulic drive engaged.

MD 089

Risk of crushing of whole body in the danger
area of suspended loads/machine parts

This danger can cause extremely serious and
potentially fatal injuries.

The presence of persons under suspended
loads/machine parts is prohibited.

Maintain a sufficient safety clearance between
you and any suspended loads/machine parts.

Ensure that all personnel maintain a sufficient
safety clearance from suspended loads/machine
parts.

Direct persons out of the danger area of sus-
pended loads/machine parts.

Содержание ZA-M Profis Hydro









































































































Результаты поиска

Содержание ZA-M Profis Hydro

Отзывы:

Бренды по названию

Популярные бренды

Amazone ZA-M Profis Hydro, Руководство по эксплуатации

Результаты поиска

Содержание ZA-M Profis Hydro

Отзывы:

Бренды по названию

Популярные бренды