Amazone ZA-M Profis Hydro Скачать руководство пользователя страница 86

Страница: 86 / 104

Faults

ZA-M BAG0040.8 09.15

11.3

Faults, causes and remedies

Fault

Cause

Remedy

Fertiliser lateral distribution not
uniform

Fertiliser deposits on the spread-
ing discs and the spreading
vanes.

Clean the spreading discs and
the spreading vanes.

Sliders do not open all the way.

Too much fertiliser in the tractor
track

Prescribed spreading disc speed
is

not

reached.

Increase tractor engine speed.

Spreading vanes and outlets
defective or worn.

Check the spreading vanes and
outlets. Replaced defective or
worn parts immediately.

The spreading properties of your
fertiliser differ from those of the
one we tested when creating the
setting chart.

Contact the

AMAZONE

Fertiliser Service.



05405-501-111

Too much fertiliser in the overlap
area

Prescribed spreading disc speed
is exceeded.

Reduce tractor engine speed.

The spreading properties of your
fertiliser differ from those of the
one we tested when creating the
setting chart.

Contact the

AMAZONE

Fertiliser Service.



+49 5405 501 - 111

Both hopper tips do not empty
uniformly at the identical slider
position

Bridging of fertiliser.

Eliminate cause of bridging.

R-clip in the spiral agitator has
shorn off due to overloading.

Replace R-clip.

Basic settings of the sliders differ Check basic settings of the slid-

ers.

Hydraulic cylinders are not open-
ing or closing

Fluid supply at the tractor is not
switched on.

Switch on fluid supply at the trac-
tor.

Power supply to valve block in-
terrupted.

Check cable, plug and contacts.

Oil filter contaminated.

Replace/clean oil filter.

Solenoid valve contaminated.

Rinse solenoid valve.

The temperature of the hydraulic
fluid is too high in a tractor
equipped with a constant flow
system (gear pump)

The system converting bolt on
the spreader valve block has not
been unscrewed to the limit stop
(factory setting).

Unscrew the system converting
bolt on the spreader valve block
until it reaches the limit stop

Defective plug couplings

Check plug couplings, re-
pair/replace as required.

Defective tractor control unit

Check tractor control unit, re-
pair/replace as required.

Содержание ZA-M Profis Hydro









































































































Результаты поиска

Содержание ZA-M Profis Hydro

Отзывы:

Бренды по названию

Популярные бренды

Amazone ZA-M Profis Hydro, Руководство по эксплуатации

Результаты поиска

Содержание ZA-M Profis Hydro

Отзывы:

Бренды по названию

Популярные бренды