background image

4

5

  f)  If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) or ground fault circuit interrupter (GFCI ) 

protected supply. Use of a RCD or GFCI reduces the risk of electric shock.

3) Personal Safety

  a)  Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under 

the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

  b)  Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or 

hearing protection used for appropriate conditions will reduce personal injury.

  c)  Prevent unintentional starting. Ensure switch is in off-position before connecting to power source and/or battery pack, picking up, or carrying 

the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.

  d)  Remove any adjustment wrench or key before turning the power tool on. Awrench or key left attached to a rotating part of the power tool may 

result in personal injury.

  e)  Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

  f)  Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts.

  g)  Loose clothes, jewelry, or long hair can be caught in moving parts.If devices are provided for the connection of dust extraction and collection 

facilities, ensure these are connected and properly used. Use of dust collection can reduce dust related hazards. It is recommendation that the 

tool always be supplied via a residual current device with a rated residual current of 30mA or less.

4) Power Tool Use and Care

  a)  Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate 

for which it was designed.

  b)  Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and 

must be repaired.

  c)  Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories 

or storing power tools. Such preventative safety measures reduce the risk of starting the power tool accidently.

  d)  Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the 

power tool. Power tools are dangerous in the hands of untrained users.

  e)  Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power 

tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

  f)  Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

  g)  Use the power tool and accessories in accordance with these instructions, taking into account the working conditions and the work to be 

performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

  h)  Operating a tool that is not completely of fully assembled could result in injury or property damage. Do not operate this tool until it is 

completely assembled. Keep all fasteners tight. Keep adjustments per tool’s specifications.

5) Service

  a)  Have the power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power 

tool is maintained. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in 

order to avoid a hazard.

Safety Warnings for Sanding Operations

  a)  This power tool is intended to function as a sander. Read all safety warnings, instructions and specifications provided with this power tool. 

Failure to follow all instructions listed below may result in electric shock, fire, or personal injury.

  b)  Operations such as grinding, wire brushing, polishing or cutting-off, are not recommended to be performed with this power tool. Operations for 

which the tool was not designed may create a hazard and cause personal injury.

  c)  Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be 

attached to your power tool, it does not assure safe operation.

  d)  The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than 

their rated speed can break and fly apart.

  e)  The outside diameter and thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories 

cannot be adequately guard or controlled.

  f)  The arbor size of wheels, flanges, backing pads or any other accessory must fit the spindle of the power tool. Accessories with arbor holes that 

do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.

  g)  Do not use damaged accessory. Before each use inspect the accessory such as abrasive wheel for chips or cracks, backing pad for cracks, 

tear or excess wear, wire brush for loose or cracked wires. If power tool or accessory is dropped, inspect for damage or install an undamaged 

accessory. After inspecting or installing an accessory, position yourself or bystanders away from the plane of the rotating accessory and run 

the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this time.

  h)  Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust 

mask, hearing protectors, gloves and workshop apron capable of stopping flying debris generated by various operations. The eye protection 

must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of filtering particles 

generated by your operations. Prolonged exposure to high intensity noise may cause hearing loss.

  i)  Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment. Fragments 

of work piece or a broken accessory mayfly away and cause injury beyond immediate area of operation.

  j)  Hold power tool by gripping insulated surfaces (handle) only, when performing an operation where the cutting accessory may contact hidden 

wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and shock the operator.

  k)  Position the cord clear of the spinning accessory. If you loose control, the cord may be cut or snagged and your arm or hand may be pulled into 

the spinning accessory.

  l)  Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the 

power tool out of your control.

  m)  Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the 

accessory into your body.

  n)  Regularly clean the power tools air vents. The motor’s fan will draw the dust inside the housing and excessive accumulation may cause 

electrical hazards.

  o)  Do not operate the power tool near flammable materials. Sparks could ignite these materials.

  p)  Do not use excessively oversized sanding disc paper. Follow manufacturer’s recommendations when selecting sanding paper. Larger sanding 

paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback.

  q)  Risk of explosion. Floor sanding can result in an explosive mixture of fine dust and air. Use floor sanding machine only in a well-ventilated area 

free from any flame or match.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes 

rapid stalling of the rotating backing pad which in turn causes uncontrolled power tool to be forced in the opposite direction of the backing pad’s 

rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by the work piece, the edge of the wheel that is entering into the pinch point can dig into 

the surface of the material causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on 

direction of the wheel’s movement at the point of pinching. Abrasive wheels may also break under these conditions.

Kickback is the result of power tool misuse and incorrect operating procedures or conditions and can be avoided by taking proper precautions as 

given below.

  a)  Maintain a firm grip on the power tool and position your body and arms to allow you to resist kickback forces. Always use auxiliary handles, if 

provided for maximum control over kickback or torque reactions during start up. The operator can control torque reactions or kickback forces, 

if proper precautions are taken.

  b)  Never place your hand near the rotating accessory. Accessory may kickback over your hand.

  c)  Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in the direction opposite to 

the wheel’s movement at the point of the snagging.

  d)  Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have 

a tendency to snag the rotating accessory and cause loss of control or kickback.

Additional Rules for Safe Operation

  a)  Empty the dust bag or dust collection receiver frequently. Do not leave residue in dust bag or dust collection receiver unattended. Always empty 

in a non-combustible metal container. Sanding wood or varnish produces dust that can self ignite and cause injury or damage. Follow this 

precaution for storage.

  b)  Setall exposed nails. Sweep loose abrasive away from work area. Do not strike metal pipes, ect., with sanding paper. Striking metal or abrasive 

particles with sanding paper produces sparks that could ignite the sanding dust which can cause injury or damage.

  c)  Do not operate a partially assemble power tool. Keep all adjustments within manufacturer’s specifications. Keep all fasteners tight. Operating 

a partially assembled power tool could result in injury to the operator or bystander and could cause damage to the equipment or surroundings.

  d)  Do not attempt to change the sanding paper while the power tool is running. The sanding pad can snag clothing and cause injury to limbs and 

moving sanding paper can cause abrasions.

  e)  The power tool should only be used on an electrical system (mains) that is rated for the electrical requirements of the power tool as shown on 

the nameplate. Use only on an earthing (grounded) system. Do not service the power tool if it is energized or connected to an electrical circuit. 

Improper use could cause fire or electric shock.

EN

EN

Содержание American Sanders EZ-E






















Отзывы: