10
Machine Set-up
EN
WARNING:
Injury could occur to the operator or bystanders if the
machine should tip or fall while replacing the pad or
changing the abrasive.
WARNING:
Never allow the machine to be started while tilted up.
Severe injury could result if the machine is started
while the abrasive is being changed.
CAUTION:
Damage to the sanding head will occur if the unit is
allowed to drop freely from the tilted position.
CAUTION:
Damage to the pad driver will occur if the machine
is operated without sandpaper or screen and pad.
Damage to the pad driver can also occur if the pad
is less than 1/8” thick.
10. Install or replace sandpaper or screen and pad. The sandpaper,
screen, and pad should be replaced if there are any tears or if they
have become worn and dull. The pad should also be replaced if
its thickness is less than 1/8”. To install or replace the sandpaper,
screen, or pad: (See Figure 12)
DANGER: Disconnect the power source. Electrocution
could occur if the machine is connected to
the power source while changing the abra-
sives, pads or empting the dust bag.
a.)
Unplug the machine from its power source and move
the power cord out of your way.
b.)
Tilt the machine back by pressing on the tilt assist strap
with your foot while also pushing down on the handle.
(see Figure 13)
c.)
Remove foot from tilt assist strap and continue to push
down on the handle until the machine rests in the up
position on the handle and tilt wheels. (see Figure 14)
d.)
To remove the existing paper or screen / pad stand to
the side of the machine and pull from one edge. The
screen may have a plastic pushpin in the center that
will require removing prior to the screen’s removal.
(See Figure 15)
e.)
Center the new paper or screen / pad over the pad
driver and press against the pad driver until the hooks
on the driver hold them in position.
WARNING:
The machine is heavy. Keep others away from the
machine because of possible injury if the machine
should tip or fall. When replacing the pad or changing
the abrasive use caution when tilting the machine. The
operator or other bystanders could be injured.
f.)
Return the machine to upright position by standing
behind the handle and raising it from the floor until the
caster wheels contact the floor. Place your foot on the
tilt assist strap and ease the sanding unit to the floor.
11. Connect the vacuum hose to the sanding unit and vacuum.
12. Connect the power cord to the electric box.
Figure 12
Figure 15
Figure 13
Figure 14
Содержание 07082C
