Altigen AltiWare OE 4.6 Скачать руководство пользователя

Страница: 212 / 518

Configuring the Triton T1/PRI Board

6-30

AltiWare OE System Installation & Administration Manual

CSU/DSU - ADTRAN T1 ACE (recommended) or other CSU/DSU

Technical Information for T1 with Voice

Signaling Protocol:

• E&M Wink Start (recommended)

• E&M Immediate Start

• Ground Start

• Loop Start (not recommended)

Trunk Type:

• DID

• 2-Way DID (recommended)

• DOD

Framing:

• Super Frame (SF)/D4

• Extended Super Frame (ESF) (recommended)

Line Coding:

• Alternate Mark Inversion (AMI)

• B8ZS (recommended)

DNIS, Caller ID - DTMF (Dual Tone Multi-Frequency)

Physical Termination - RJ-48X or RJ-48C

Wire: 4 wires

800 Service: you decide

Termination Impedance - 100 ohms

Type of Registered Services Provided

BN 1.544 Mbps SF without power

DN 1.544 Mbps SF B8ZS without power

1KN 1.544 Mbps ANSI ESF without power

1SN 1.544 Mbps ANSI ESF, B8ZS without power (recommended)

Service Order Code

SOC 6.0P AS.2

Содержание AltiWare OE 4.6







































































































































































































































































































































































































































































































































Результаты поиска

Содержание AltiWare OE 4.6

Отзывы:

Похожие инструкции для AltiWare OE 4.6

Бренды по названию

Популярные бренды

Altigen AltiWare OE 4.6, Руководство администратора

Результаты поиска

Содержание AltiWare OE 4.6

Отзывы:

Похожие инструкции для AltiWare OE 4.6

Бренды по названию

Популярные бренды