manualshive.com logo in svg

Altera PHY IP Core, Руководство пользователя

Поделиться
Скачать
Altera PHY IP Core Скачать руководство пользователя страница 56

4–14

Chapter 4: XAUI PHY IP Core

Interfaces

Altera Transceiver PHY IP Core

March 2012

Altera Corporation

User Guide

Table 4–9

 describes the signals in the SDR TX XGMII interface. 

SDR XGMII RX Interface

Table 4–10

 describes the signals in the SDR RX XGMII interface. 

Transceiver Serial Data Interface

Table 4–11

 describes the signals in the XAUI transceiver serial data interface. There are 

four lanes of serial data for both the TX and RX interfaces. This interface runs at 
3.125 GHz or 6.25 GHz depending on the variant you choose. There is no separate 
clock signal because it is encoded in the data.

Table 4–9. SDR TX XGMII Interface 

Signal Name

Direction

Description

xgmii_tx_dc[71:0]

Source

Contains 4 lanes of data and control for XGMII. Each lane consists of 
16 bits of data and 2 bits of control.

■

Lane 0–[7:0]/[8], [43:36]/[44]

■

Lane 1–[16:9]/[17], [52:45]/[53]]

■

Lane 2–[25:18]/[26], [61:54]/[62]

■

Lane 3–[34:27]/[35],[70:63]/[71]

xgmii_tx_clk

Input

The XGMII SDR TX clock which runs at 156.25 MHz or 312.5 for the 
DDR variant.

Table 4–10. SDR RX XGMII Interface 

Signal Name

Direction

Description

xgmii_rx_dc[71:0]

Sink

Contains 4 lanes of data and control for XGMII. Each lane consists of 
16 bits of data and 2 bits of control.

■

Lane 0–[7:0]/[8], [43:36]/[44]

■

Lane 1–[16:9]/[17], [52:45]/[53]]

■

Lane 2–[25:18]/[26], [61:54]/[62]

■

Lane 3–[34:27]/[35],[70:63]/[71]

xgmii_rx_clk

Output

The XGMII SDR RX MAC interface clock which runs at 156.25 MHz.

Table 4–11. Serial Data Interface 

Signal Name

Direction

Description

xaui_rx_serial_data[3:0]

Input

Serial input data.

xaui_tx_serial_data[3:0]

Output

Serial output data.

Содержание PHY IP Core







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды