manualshive.com logo in svg

Altera PHY IP Core, Руководство пользователя

Поделиться
Скачать
Altera PHY IP Core Скачать руководство пользователя страница 179

Chapter 10: Transceiver Reconfiguration Controller

10–13

EyeQ

March 2012

Altera Corporation

Altera Transceiver PHY IP Core

User Guide

EyeQ uses a phase interpolator and sampler to estimate the vertical and horizontal 
eye opening using the values that you specify for the 

horizontal phase

 and 

vertical 

height

. (Refer to 

Table 10–12 on page 10–14

.) The phase interpolator generates a 

sampling clock and the sampler examines the data from the receiver output. The 
sampled data is deserialized and sent to the IP core where the PRBS checker 
determines the BER. As the phase interpolator output clock phase is shifted by small 
increments, the data error rate goes from high to low to high if the receiver is good. 
The number of steps of valid data is defined as the width of the eye. If none of the 
steps yields valid data, the width of the eye is equal to 0, which means the eye is 
closed.

Table 10–11

 lists the memory-mapped EyeQ registers that you can access using 

Avalon-MM reads and writes on reconfiguration management interface. 

1

All undefined register bits are reserved.

Table 10–11.  Eye Monitor Registers 

Recon

-fig 

Addr

Bits

R/W

Register Name

Description

7’h10

[9:0]

RW

logical channel number

The logical channel number. Must be specified when 
performing dynamic updates. The Transceiver 
Reconfiguration Controller maps the logical address to the 
physical address.

7’h12

[9]

R

control and status

Error

. When asserted, indicates an invalid channel or 

address.

[8]

R

Busy

. When asserted, indicates that a reconfiguration 

operation is in progress. 

[1]

W

Read

. Writing a 1 to this bit triggers a read operation.

[0]

W

Write

. Writing a 1 to this bit triggers a write operation.

7’h13

[5:0]

RW

eyeq offset

Specifies the 6-bit offset of the EyeQ register.

7’h14

[15:0]

RW

data

Reconfiguration data for the transceiver PHY registers.

Содержание PHY IP Core







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды