manualshive.com logo in svg

Altera PHY IP Core, Руководство пользователя

Поделиться
Скачать
Altera PHY IP Core Скачать руководство пользователя страница 102

7–2

Chapter 7: Custom PHY IP Core

Device Family Support

Altera Transceiver PHY IP Core

March 2012

Altera Corporation

User Guide

Figure 7–1

 illustrates the top-level signals and modules of the Custom PHY.

f

For more detailed information about the Custom datapath and clocking, refer to the 
“

Custom Configurations with the Standard PCS

” section in the 

Transceiver Custom 

Configurations in Stratix V Devices 

chapter of the 

Stratix V Device Handbook

.

Device Family Support

IP cores provide either final or preliminary support for target Altera device families. 
These terms have the following definitions:

■

Final support—V

erified with final timing models for this device.

■

Preliminary support

—Verified with preliminary timing models for this device.

Table 7–1

 shows the level of support offered by the Custom PHY IP core for Altera 

device families.

Performance and Resource Utilization

Because the PCS and PMA are both implemented in hard logic, the Custom PHY IP 
core requires less than 1% of FPGA resources. 

Table 7–1

 lists the resource utilization 

for the Custom PHY when the 1.25GbE preset is specified. 

Figure 7–1. Custom PHY IP Core

Custom PHY IP Core

Tx Serial Data

Avalon-ST Tx and Rx

Rx Serial Data

to

ASIC,

ASSP,

FPGA,

or

Backplane

from

Custom

MAC

Stratix V FPGA

PCS:

8

B/10B

Word Aligner

Rate Match FIFO

Byte Ordering

PMA:

Analog Buffers

SERDES

Avalon-MM Cntrl and Status

Avalon-ST Reconfig

Table 7–1. Device Family Support

Device Family

Support

Stratix V devices–Hard PCS and PMA

Preliminary

Arria V devices–Hard PCS and PMA

Preliminary

Cyclone V devices–Hard PCS and PMA

Preliminary

Other device families

No support

Table 7–2. Custom PHY IP Core Performance and Resource Utilization—Stratix V GT Device

Channels

Combinational ALUTs

Logic Registers (Bits)

1

142

154

4

244

364

Содержание PHY IP Core







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды