manualshive.com logo in svg

Altera PHY IP Core, Руководство пользователя

Поделиться
Скачать
Altera PHY IP Core Скачать руководство пользователя страница 123

Chapter 7: Custom PHY IP Core

7–23

Interfaces

March 2012

Altera Corporation

Altera Transceiver PHY IP Core

User Guide

0x066

[31:0]

R

pma_rx_is_lockedtodata

When 1, indicates that the RX CDR PLL is locked to the RX 
data, and that the RX CDR has changed from LTR to LTD 
mode. Bit 

<n>

 corresponds to channel 

<n>

.

0x067

[31:0]

R

pma_rx_is_lockedtoref

When 1, indicates that the RX CDR PLL is locked to the 
reference clock. Bit 

<n>

 corresponds to channel 

<n>

.

Custom PCS 

0x080

[31:0]

RW

Lane or group number

Specifies lane or group number for indirect addressing, 
which is used for all PCS control and status registers. For 
variants that stripe data across multiple lanes, this is the 
logical group number. For non-bonded applications, this is 
the logical lane number. 

0x081

[5:1]

R

rx_bitslipboundaryselect

out

This is an output from the bit slip word aligner which shows 
the number of bits slipped.

F

r

om block:

 Word aligner.

[0]

R

rx_phase_comp_fifo_error

When set, indicates an RX phase compensation FIFO error.

F

r

om block:

 RX phase Compensation FIFO

0x082

[0]

RW

tx_phase_comp_fifo_error

When set, indicates an TX phase compensation FIFO error.

F

r

om block:

 TX phase Compensation FIFO

0x083

[5:1]

RW

tx_bitslipboundary_select

Sets the number of bits that the TX bit slipper needs to slip.

To block:

 Word aligner.

[0]

RW

tx_invpolarity

When set, the TX interface inverts the polarity of the TX 
data.

To block

: 8B/10B encoder.

0x084

0

RW

rx_invpolarity

When set, the RX channels inverts the polarity of the 
received data.

To block

: 8B/10B decoder.

0x085

[3]

RW

rx_bitslip

Every time this register transitions from 0 to 1, the RX data 
slips a single bit.

To block:

 Word aligner.

[2]

RW

rx_bytereversal_enable

When set, enables byte reversal on the RX interface.

To block: 

Byte deserializer.

[1]

RW

rx_bitreversal_enable

When set, enables bit reversal on the RX interface. 

To block:

 Word aligner.

[0]

RW

rx_enapatternalign

When set in manual word alignment mode, the word 
alignment logic begins operation when this pattern is set.

To block:

 Word aligner.

Table 7–21. Custom PHY IP Core Registers  (Part 3 of 3)

 

Word 

Addr

Bits

R/W

Register Name

Description

Содержание PHY IP Core







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды