Altera EP2AGX125 Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 144

background image

Chapter 5: Clock Networks and PLLs in Arria II Devices

5–3

Clock Networks in Arria II Devices

December 2010

Altera Corporation

Arria II Device Handbook Volume 1: Device Interfaces and Integration

Global Clock Networks

Arria II devices provide up to 16 GCLKs that can drive throughout the device, serving
as low-skew clock sources for functional blocks such as adaptive logic modules
(ALMs), digital signal processing (DSP) blocks, embedded memory blocks, and PLLs.
Arria II I/O elements (IOEs) and internal logic can drive GCLKs to create internally
generated GCLKs and other high fan-out control signals; for example, synchronous or
asynchronous clears and clock enables.

and

show CLK pins and

PLLs that can drive GCLK networks in Arria II devices.

Figure 5–1. GCLK Networks in Arria II GX Devices

Notes to

Figure 5–1

(1)

PLL_5

and

PLL_6

are only available in EP2AGX95, EP2AGX125, EP2AGX190, and EP2AGX260 devices.

(2) Because there are no dedicated clock pins on the left side of an Arria II GX device,

GCLK[0..3]

are not driven by any clock pins.

GCLK[0..3] (

2

)

GCLK[4..7]

CLK[4..7]

GCLK[8..11]

CLK[8..11]

CLK[12..15]

Center PLLs

Top Right PLL

Top Left PLL

Bottom Left PLL

Bottom Right PLL

GCLK[12..15]

PLL_1

PLL_2

(1)

(1)

PLL_3

PLL_5

PLL_6

PLL_4

«
...
93
94
95
96
97
...
»

Содержание EP2AGX125

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для EP2AGX125

Бренд: Yamaha Страницы: 83

Бренд: E-peas Страницы: 2

Бренд: Biostar Страницы: 45

Бренд: SOLTEK Страницы: 72

Бренд: Avalue Technology Страницы: 82

Бренд: Gigabyte Страницы: 116

Бренд: JETWAY Страницы: 48

Бренд: Microsemi Страницы: 22

Бренд: Gigabyte Страницы: 112

Бренд: Texas Instruments Страницы: 17

Бренд: Aaeon Страницы: 108

Бренд: TYAN Страницы: 86

Бренд: Supermicro Страницы: 97

Бренд: Gigabyte Страницы: 39

Бренд: Gigabyte Страницы: 96

Бренд: Gigabyte Страницы: 147

Supero X9DRW-7TPF

Бренд: Supero Страницы: 119

STEVAL-IHM011V1

Бренд: ST Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды