Altera EP2AGX125 Скачать руководство пользователя страница 117

Страница: 117 / 144

Chapter 5: Clock Networks and PLLs in Arria II Devices

5–25

PLLs in Arria II Devices

December 2010

Altera Corporation

Arria II Device Handbook Volume 1: Device Interfaces and Integration

PLL Control Signals

You can use the

pfdena

areset

, and

locked

signals to observe and control PLL

operation and resynchronization.

pfdena

Use the

pfdena

signal to maintain the most recent locked frequency to allow your

system to store its current settings before shutting down. The

pfdena

signal controls

the phase frequency detector (PFD) output with a programmable gate. If you disable
the PFD, the VCO operates at its most recent set value of control voltage and
frequency with some long-term drift to a lower frequency.

areset

The

areset

signal is the reset or resynchronization input for each PLL. The device

input pins or internal logic can drive these input signals. When

areset

is driven high,

the PLL counters reset, clearing the PLL output and placing the PLL out-of-lock. The
VCO is then set back to its nominal setting. When

areset

is driven low again, the PLL

resynchronizes to its input as it relocks.

You must include the

areset

signal in designs if any of the following conditions are

true:

■

PLL reconfiguration or clock switchover is enabled in your design.

■

Phase relationships between the PLL input and output clocks must be maintained
after a loss-of-lock condition.

If the input clock to the PLL is not toggling or is unstable after power up, assert the

areset

signal after the input clock is stable and in specifications.

locked

The

locked

signal indicates that the PLL has locked onto the reference clock and the

PLL clock outputs are operating at the desired phase and frequency set in the
Quartus II software.

Altera recommends using the

areset

and

locked

signals in your designs to control

and observe the status of your PLL.

For more information about the PLL control signals, refer to the

ALTPLL Megafunction

User Guide

Содержание EP2AGX125

















































































































































Результаты поиска

Содержание EP2AGX125

Отзывы:

Похожие инструкции для EP2AGX125

Бренды по названию

Популярные бренды

Altera EP2AGX125, Руководство по эксплуатации устройства

Результаты поиска

Содержание EP2AGX125

Отзывы:

Похожие инструкции для EP2AGX125

Бренды по названию

Популярные бренды