Allnet ALL-NAS1000 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 137

Allnet ALL-NAS1000 Скачать руководство пользователя страница 20

20

Once you are logged in as an administrator disclaimer page will appear as below.
Please click the check box if you do not want to have this page displayed during the
next login.

Following by disclaim page, you will see the Web Administration Interface.
From here, you can configure and monitor virtually every aspect of the ALLNET IP
storage from anywhere on the network.

My Favorite

The user interface with “My Favorite” shortcut is allowed user to designate often
used items and have them display on the main screen area. The figure below
displays system favorite functions.

Administrators can add or remove favorite functions to My Favorites by right
clicking the mouse on the menu tree.

The other way administrators can add favorite functions is by clicking the “Add

Favorite” icon in each function screen. Please refer figure below in red circuit icon.

«
...
18
19
20
21
22
...
»

Содержание ALL-NAS1000










































































































































Отзывы:

Нет отзывов