Allnet ALL-NAS1000 Скачать руководство пользователя страница 120

Страница: 120 / 137

120

Uninterrupted Power Source

From the External Devices menu, choose the Uninterrupted Power Source
item and the UPS Setting screen appears. Make any changes you wish, and press
Apply to confirm changes.

See the following table for a detailed description of each item.

UPS Setting

Item

Description

UPS Monitoring

Enable or disable UPS monitoring.

Remote UPS Monitoring

Enable or disable Remote UPS monitoring.

Remote UPS IP

Input the IP address of the NAS that the UPS device
is connected to via USB or RS232.Input the IP
address of your network UPS.

Manufacturer

Choose the UPS manufacturer from the
dropdowns.

Model

Choose the UPS model number from the
dropdowns.

Battery Status

Current status of the UPS battery

Power

Current status of the power being supplied to the
UPS

Содержание ALL-NAS1000










































































































































Результаты поиска

Содержание ALL-NAS1000

Отзывы:

Allnet ALL-NAS1000, Руководство пользователя, Страница: 120 / 137

Результаты поиска

Содержание ALL-NAS1000

Отзывы: