Allied Leister GEOSTAR G5 Скачать руководство пользователя

Страница: 8 / 35

The LED of the

Drive “On/Off” key (30)

shows the condition of the drive when it is working as intended.

LED status (31)

Drive On/Off (30)

Condition

Cause

LED off

Drive is switched off.

LED continuously green

Drive is switched on.

If, during operation of the drive, a warning message occurs in the

Status display area 2 (36)

or if there is an

error message in the

working display (34),

then this will be displayed as follows:

LED flashes red

Drive current limiting is active.

See warning and error message.

LED continuously red

The drive has an error.

See warning and error message.

Keyboard mode

Current selection

Working display

Current selection

function display

Current selection

Set-up menu

Up (27)

Down (28)

Changes the position
within the working
display.

Switches from
function display to
working display.

Changes the position
within the Setup menu.

Heating

On/Off (29)

Switched heating
on/off

No function

Drive

On/Off (30)

Switches drive
on/off

No function

Press

«e-Drive» (32)

Set value is adopted
straight away and
the selection jumps
straight back to the
function display.

Selected
function is
executed.

Selection of the marked
position.

Rotate

«e-Drive» (32)

Setting the desired
setpoints in 5 °C or
0.1 m/min increments

Changing the
position in the
Function display.

•

Changes the position
within the Setup menu

• Setting the value of the

selected position

5.4 Status LED display “Drive”

5.5 Operating unit description

Содержание Leister GEOSTAR G5




































Результаты поиска

Содержание Leister GEOSTAR G5

Отзывы:

Похожие инструкции для Leister GEOSTAR G5

Бренды по названию

Популярные бренды

Allied Leister GEOSTAR G5, Руководство пользователя

Результаты поиска

Содержание Leister GEOSTAR G5

Отзывы:

Похожие инструкции для Leister GEOSTAR G5

Бренды по названию

Популярные бренды