Allied Leister GEOSTAR G5 Скачать руководство пользователя

Страница: 32 / 35

14. Warnings and error messages

• If there is a warning pending, the user can continue to work. You can access more detailed information about the

warning via the

function display (33)

by selecting “Warnings” in the

Settings

menu.

• If a warning occurs while welding, this can be displayed with the

“Up” key

• If an error occurs, the heating is switched off and the drive is no longer released.
• If the drive is blocked, switch off the

main switch (2)

and disconnect the

power cord (1)

from the mains. Contact

a Leister service center.

Type of

message

Display

Error code/

warning message

Error description

Ambient Temperature

Ambient temperature is too high

Undervoltage

Overvoltage

Max. Force Exceeded

Max. clamping force exceeded

Drive Overcurrent

Current limitation

Error

0001.XXXX

Device has overheated.
Allow the device to cool down.

Error

0002.XXXX

Overvoltage or undervoltage of the mains voltage.
Check voltage source.

Error*

0004.XXXX

Hardware error

0008.XXXX

Thermocouple is defective

0020.XXXX

Heating cartridge is defective

0200.XXXX

Communication error

0400.XXXX

Drive error

*Contact Leister Service Center

Содержание Leister GEOSTAR G5




































Результаты поиска

Содержание Leister GEOSTAR G5

Отзывы:

Похожие инструкции для Leister GEOSTAR G5

Бренды по названию

Популярные бренды

Allied Leister GEOSTAR G5, Руководство пользователя

Результаты поиска

Содержание Leister GEOSTAR G5

Отзывы:

Похожие инструкции для Leister GEOSTAR G5

Бренды по названию

Популярные бренды