Allied BreakerLube CML Series Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 62

background image

Allied Construction Products, LLC www.alliedcp.com

12

TM102783_BreakerLube CML_15jul

6.0 Installation – [cont’d]

6.3.1 (F) - Single Element Into Single Lube Line

Fig. 6-2 Single Pump Element & Lube Line

1. If not already installed, refer to instructions in

Section 6.6 for installing the pump element and
relief valve assembly.

2. Route lube lines along the existing hydraulic

hoses. Allow for proper slack at pivot joints.

IMPORTANT

Route hoses avoiding sharp bends. Wrap any hose
susceptible to damage from rubbing. Before cutting
hose, check for proper length to both termination
points, knowing where each component mounts.

3. Measure, cut and assemble connectors to lube

lines according to figure 6-3. Quick disconnect
couplers are provided for easy connection and
removal of the breaker.

Fig. 6-3 Cut-to-Length and Assemble Lube Lines

4. Secure lube lines with supplied nylon ties.

5. For the location of port ‘G’, refer to breaker’s

Operating Manual. Location of the ‘G’ port can
vary. Typical location is on the valve housing or
back head. The port is marked “G”.

6.3.2 (G) - Two Elements Into Single Lube Line

Fig. 6-4 Add 2

nd

Pump & Bridge into 1 Lube Line

1. If not already installed, refer to the pump element

instructions in Section 6.6. Refer to above figure
for assembly of 2-element adapter kit.

2. Route lube lines along the existing hydraulic

hoses. Allow for proper slack at pivot joints.

IMPORTANT

Route hoses avoiding sharp bends. Wrap any hose
susceptible to damage from rubbing. Before cutting
hose, check for proper length to both termination
points, knowing where each component mounts.

3. Measure, cut and assemble connectors to lube

lines according to figure 6-3. Quick disconnect
couplers are provided for easy connection and
removal of the breaker.

4. Secure lube lines with supplied nylon ties.

5. For the location of port ‘G’, refer to breaker’s

Operating Manual. The port location can vary.
Typical location is on the valve housing or back
head. The port is marked “G”.

-MIN-

-MAX-

BreakerLube

F

Cut to length

Cut to length

-MIN-

-MAX-

G

«
...
20
21
22
23
24
...
»

Содержание BreakerLube CML Series































































Отзывы:

Нет отзывов

Похожие инструкции для BreakerLube CML Series

Бренд: JABSCO Страницы: 32

Бренд: Eaton Страницы: 2

Бренд: Salamander Pumps Страницы: 32

Бренд: Larius Страницы: 46

Бренд: Rheem Страницы: 28

Altherma EKHWE150A3V3

Бренд: Daikin Страницы: 10

Бренд: EBARA Страницы: 48

Бренд: Powerhorse Страницы: 48

Бренд: AL-KO Страницы: 144

Бренд: Acquaer Страницы: 12

Бренд: VONROC Страницы: 60

Бренд: RainScapes Страницы: 2

Бренд: Redring Страницы: 4

Бренд: Little Giant Страницы: 2

Бренд: Ingersoll-Rand Страницы: 12

CronoBloc BL Series

Бренд: Wilo Страницы: 43

Бренд: A.O. Smith Страницы: 16

Бренд: Giant Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды