manualshive.com logo in svg

Allied Telesis Rapier 16fi, Справочник по аппаратуре, Страница: 63 / 65

Поделиться
Скачать
Allied Telesis Rapier 16fi Скачать руководство пользователя страница 63

Hardware Reference

63

C613-03020-00 REV K

Figure 32: Example output from the SHOW INSTALL command

Troubleshooting EPROM Installation

If the switch fails to reboot or functions incorrectly, then the most likely cause is 
that there is a problem with the way the boot EPROMs were installed. Repeat 
the installation procedure, checking:

•

That the boot EPROMs are in the correct locations and oriented 
correctly (using the relevant location diagram as a guide).

•

For bent pins. These should be carefully straightened.

If the switch still fails to reboot, replace the new boot EPROMs with the 
original set and contact your Authorised Allied Telesis distributor or reseller.

Install     Release                   Patch

------------------------------------------------------------

Temporary   -                           -

Preferred   flash:load\86s-210.rez      -

Default     EPROM (86s-2.1.0)           -

------------------------------------------------------------

 

Current install

------------------------------------------------------------

Preferred   flash:load\86s-210.rez      -

------------------------------------------------------------

 

Install history

------------------------------------------------------------

No Temporary install selected

Preferred install selected

Preferred release successfully installed

------------------------------------------------------------

Содержание Rapier 16fi


































































Отзывы:

Нет отзывов