Allied Telesis Rapier 16fi Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 65

Allied Telesis Rapier 16fi Скачать руководство пользователя страница 39

Hardware Reference

39

C613-03020-00 REV K

Table: 21 LEDs on the AT-A42/GBIC Uplink Module

LED

State

Function

L/A

Link/Activity

Green

A 1000 Mbps link is open

Flashing green

1000 Mbps activity is occurring

Flashing amber
(and GBIC LED is
Off)

A TX fault has occurred

Off

No link is present

GBIC

Green

The switch has recognised the GBIC, the
GBIC is a valid model

Green
(and L/A LED is
flashing GREEN)

The port is operating at full-duplex

Amber
(and L/A LED is
OFF)

The switch has not recognised the GBIC, the
GBIC is not a valid model

Amber
(and L/A LED is
flashing GREEN)

The port is operating at half-duplex

Flashing amber
(and L/A LED is
flashing GREEN)

Collisions are occurring

Off

No GBIC is installed, or a TX fault has
occurred

Both LEDs

Slow alternate
flashing of L/A and
GBIC LED, amber

The switch has not recognised the GBIC, or
the GBIC is not a valid model

«
...
37
38
39
40
41
...
»

Содержание Rapier 16fi


































































Отзывы:

Нет отзывов