Allied Systems Allied H6G Series Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 122

background image

Section 4

4 - 33

NOTE: Lubricate all rubber components with clean
hydraulic fl uid before reassembly.

1.

Clean all parts thoroughly before assembling.

2.

Press oil seal (item 4) into cover plate (item 5) until
fl ush with bearing shoulder.

NOTE: Oil seal must

be installed with open side facing pilot end of
cover.

3.

Press bearing (item 3) into position until it bottoms
out on oil seal borestep.

4.

Install retaining ring (item 2) into cover plate.

5.

Press spline shaft assembly (item 6) into bearing
(item 3) until shaft bottoms on shaft shoulder. Bear-
ing inner race must be supported during this opera-
tion.

6.

Install retaining ring (item 1) on spline shaft assembly
(item 6).

7.

Install back-up rings (items 17 & 19) on piston (item
16) toward spring pockets.

8.

Install O-rings (items 18 & 20) on piston (item 16). Be
sure O-rings are fl at and all twists removed.

NOTE:

Be careful not to mar or scratch piston.

9.

Lubricate piston (item 16) with clean hydraulic fl uid.
Carefully press piston into pressure plate (item 22).
Be sure piston is positioned so threaded holes in
piston are in alignment with through-holes in spring
plate (item 14) when installed.

10. Install springs (item 15) according to pattern and

color recorded during disassembly.

11. Affi x case gaskets (item 11) to pressure plate (item

22) and plate (item 14).

12. Place unit on a press. Using a fixture, depress

and install four socket head assembly bolts (item
12).

NOTE: Apply two drops of Loctite #242 to

threads.

13. Install stator discs (item 10) and rotor discs (item

9). Begin with a rotor disc and alternate with stator
discs.

NOTE:

The minimum stack height of discs item 9 and
item 10 is 1.173”.

14. Install primary disc (item 8). Align tabs on primary

disc with through-holes in spring plate (item 14) and
partially screw in four socket head shoulder bolts
(item 7).

NOTE: Apply two drops of Loctite #242

to threads.

Inspect for free movement of stack.

Pressurize brake release port to approximately 400
psi to release discs. Torque shoulder bolts 15-18 lb.
ft. (20.3-24.4 Nm) and release pressure. A suitable
holding fi xture is useful to hold brake in position.

15. Install cover plate (item 5) using four socket head

assembly bolts (item 23).

NOTE: Apply two drops

of Loctite #242 to threads.

Torque capscrews 55-60

lb. ft. (74.6-81.4 Nm).

«
...
91
92
93
94
95
...
»

Содержание Allied H6G Series



























































































































Отзывы:

Нет отзывов

Похожие инструкции для Allied H6G Series

Бренд: SVERO Страницы: 20

Бренд: Smittybilt Страницы: 24

Бренд: Wahlberg Страницы: 6

Бренд: Harken Страницы: 2

Бренд: HADEF Страницы: 35

NINJA 20SPS12-CAD

Бренд: Warrior Winches Страницы: 25

Бренд: Gude Страницы: 8

Бренд: Gude Страницы: 49

Бренд: Gude Страницы: 80

Бренд: Gude Страницы: 80

Бренд: FTS Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды