manualshive.com logo in svg

Allied Systems Allied H6G Series, Руководство по обслуживанию

Поделиться
Скачать
Allied Systems Allied H6G Series Скачать руководство пользователя страница 91

 Section 4

4 - 31

1. 

Press bearing cups (items 4 & 7) into each side of 
hub (item 6). It is recommended that bearing cups 
and cones (items 3 & 8) be replaced in sets.

2. 

Assemble bearing cone (item 3) into cup (item 4) at 
seal end of hub (item 6). Press a new seal (item 2) 
in until fl ush with face of hub.

3. 

Lubricate lips of oil seal (item 2) and lower hub onto 
output shaft (item 1). Keep hub centered to prevent 
damage to oil seal.

4. 

Assemble bearing cone (item 8) over output shaft 
(item 1) and into bearing cup (item 7). Install thrust 
washer (item 9) over output shaft (item 1). If bearings, 
hub or output shaft are replaced, a new retaining ring 
(item 10) is required for proper bearing setting. Select 
the thickest retaining ring that can be assembled in 
ring groove of the splined end of output shaft and 
above bearing cone (item 8). Bearing should have 
from .000 to .006 (.00 to .15 mm) end play when 
proper retaining ring is installed.

5. 

Clean mating surfaces and apply a bead of silicone 
sealant to the face of the hub that mates with the 
ring gear (item 11). See instructions on sealant pack-
age.

6. 

Assemble ring gear (item 11) to hub. Be sure to align 
all bolt holes.

7. 

Place carrier assembly (item 12) into ring gear while 
aligning gear teeth. Carrier splines mesh with splines 
on output shaft (item 1).

8. 

Place sun gear (item 13) into carrier assembly (item 
12). Sun gear should turn freely by hand.

9. 

Apply a bead of silicone sealant to cover face of ring 
gear (item 11).

10.  Secure thrust washer (item 14) with tangs engaged in 

cover (item 15). 

NOTE: Washer can be secured to 

cover with a small amount of grease or silicone 
sealant. Install the cover and align with hub such 
that pipe plug holes on cover align with mounting 
holes on hub.

11.  Install washers (item 17) and capscrews (item 

18) and torque to 40-45 lb. ft. (54-61 Nm) with dry 
threads. Lubed threads torque to 20-25 lb. ft (27-34 
Nm).

12.  Position fi ller opening horizontally and fi ll unit to oil 

level hole in cover. Install pipe plugs (items 16 & 19) 
in cover and pipe plug (item 5) in hub.

Содержание Allied H6G Series



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды