manualshive.com logo in svg

Allied Systems Allied H6G Series, Руководство по обслуживанию

Поделиться
Скачать
Allied Systems Allied H6G Series Скачать руководство пользователя страница 45

 Section 2

2 - 1

Troubleshooting

General 

Winch problems generally fall into one of three categories: 
controls, hydraulic system, or mechanical system. Follow 
the troubleshooting steps below to isolate the probable 
location of the malfunction.

1. 

Make sure the joystick control assembly (including 
pilot controller unit) is functioning properly, with a full 
range of motion.

2. 

Check the oil level and type. Ensure the operating 
temperature range for the oil is suitable for the condi-
tions. Check the fi lter indicator.

3. 

Check winch hydraulic pressures. Start with control 
pressures (see Figure 2-1), then check main system 
pressures.

4. 

Inspect the winch gear train for problems.

For best operation and life, the winch oil 
operating temperature should not exceed 
180°F (82°C). Winch oil reservoir temperature 
is monitored at the dozer. The John Deere 
750J/850J warning light will come on at 200°F 
(93°C).

John Deere 750J/850J

Pilot Control Valve Metering Curve

0

100

200

300

400

500

600

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

Lever Travel (°)

Pilot

 Pressure (

p

si)

0 psi

135.3 psi

439 psi

Normal

Deviation

Figure 2-1   Output Pressures from Pilot Controller Unit on Control Lever vs. 

Angle of Lever Defl ection

Содержание Allied H6G Series



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды