Allied Systems Allied H6G Series Скачать руководство пользователя страница 46

Страница: 46 / 122

Troubleshooting

2 - 2

Step-by-Step Pump and Controller Troubleshooting

1. Winch does not operate with the tractor running.

1.1 Is there oil in the reservoir?

Fill tractor reservoir.

Yes

Proceed to step 1.2.

1.2 Is the winch in

FREESPOOL

Proceed to step 1.3.

Yes

Shift winch out of

FREESPOOL

Function.

1.3 Is there a broken tube, loose fi tting, or burst hose?

Proceed to step 1.4.

Yes

Repair the fault.

1.4 Is the brake released?

Check brake release circuit or
mechanism.

Yes

Proceed to step 1.5.

1.5 Is the hydraulic hose routing in accordance with the hydraulic sche-

matic?

Correct the routing. Refer to the
Schematic & installation drawing.

Yes

Proceed to step 1.6.

Pilot Reducing Valve

1.6 Is there any pilot pressure from the tractor (port P at tractor interface

or pilot check port right side of dozer)?

Proceed to step 1.12.

Yes

Proceed to step 1.7.

1.7 Is the pilot standby pressure at least 275±15 psi while the dozer is

running at slow idle?

Proceed to step 1.8.

Yes

Proceed to step 1.10.

1.8 Is the pilot pressure 650 psi when the dozer blade is held over relief? No

Proceed to step 1.10.

Yes

Proceed to step 1.12.

1.10 Can the pilot pressure be increased by adjusting the tractor pilot reduc-

ing valve?

Proceed to step 1.11

Yes

Adjust to 650 psi. Proceed to 1.12.

1.11 Remove pilot reducing cartridge valve and inspect. Is it damaged?

Refit cartridge and proceed to
step 1.12.

Yes

Replace cartridge and return to
step 1.6.

Winch Control

1.12 Is lever control unit connected to pilot supply?

Connect joystick and check that
control signal RI & RO is actually
being supplied to the winch.

Yes

Proceed to step 1.13.

1.13 Is case pressure less than 35 psi?

Check drain hoses for restriction.

Yes

Proceed to step 1.14.

Содержание Allied H6G Series



























































































































Результаты поиска

Содержание Allied H6G Series

Отзывы:

Бренды по названию

Популярные бренды

Allied Systems Allied H6G Series, Руководство по обслуживанию

Результаты поиска

Содержание Allied H6G Series

Отзывы:

Бренды по названию

Популярные бренды