manualshive.com logo in svg

Allied Systems Allied H6G Series, Руководство по обслуживанию

Поделиться
Скачать
Allied Systems Allied H6G Series Скачать руководство пользователя страница 55

 Section 3

3 - 3

Standby Pilot Supply Pressure Check

With the engine shut off, connect a 1000 psi gauge to the 
tractor pilot test port. This is behind the battery access 
panel and is the quick-connect port on the pilot reducing 
manifold (see tractor Service Manual).  Start the engine 
and follow procedure in Figure 3-6. Adequate standby pilot 
supply is required for both tractor and winch functions.

If the pressure is not as specified, check for:

1. 

Improper pilot supply reducing valve setting or mal-
function (See tractor Service Manual)

2. 

Pump standby pressure setting incorrect (See tractor 
Service Manual)  

3. 

Leaking pressure hoses or fittings

Maximum Pilot Supply Pressure Check

With the same gauge installed from the Standby Pilot 
Pressure Check, bottom tractor blade cylinders and 
measure Relief Pilot Supply Pressure.  When the tractor 
pump senses a load, the maximum pilot supply pressure 
is reduced to the setting of the tractor pilot reducing valve.  
Excessive pilot supply pressure may cause damage to 
tractor and winch components.

If pressure is not as specified in Figure 3-6, check the 
following:

1. 

Improper pilot supply reducing valve setting or mal-
function (See tractor Service Manual)

2. 

Leaking pressure hoses or fittings

Figure 3-4   Hydraulic Pressure Test Ports: S/N H6G-1020 and below 

PD2

Motor B

HI-SPEED 

(HS)

FREESPOOL 

(FS)

Brake 

(BR)

HI-SPEED 

(HS)

LINE-IN 

(RI)

LINE-OUT 

(RO)

Logic

Case

Manifold

Motor A

Содержание Allied H6G Series



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды