Allied Systems Allied H6G Series Скачать руководство пользователя страница 12

Страница: 12 / 122

General

1 - 4

Specifi cations

Drum Line Capacities (Drum: 10 Inch Dia)

Hydraulic Specifi cations

Motor .............................. Dual displacement vane-type

Brake ............................... Dry multi-disc spring applied

Wire Rope Diameter

Capacity

19mm (3/4 in)

121 m (399 ft)

22mm (7/8 in.) 87 m (287 ft)
25mm (1.0 in.)

68 m (223 ft)

Note: Loosely or unevenly spooled line will change
capacities. Use fl exible cable with independent wire
rope center.

Figure 1-6 Recommended Oil List

Figure 1-4 Drum Line Capacities

Oil Specifi cations

The main consideration while selecting hydraulic fl uid is
the estimated oil temperature extremes that will be expe-

Factory fi ll is Exxon-Mobil 424. This is an ISO Viscosity
Grade 46 to 68.

For external pump winches (the winch pump uses tractor
hydraulic fl uid) the hydraulic circuit and winch gear hous-

VISCOSITY

GRADE

OIL OPERATING

TEMPERATURE RANGE

TYPICAL AMBIENT

TEMPERATURE RANGE

ISO SAE

°F

°C

°F

°C

VG 22

10W

-5 to 140

-20 to 60

-5 to 40

-20 to 4

VG 32

15W

10 to 160

-12 to 71

10 to 55

-12 to 13

VG 46

20 to 180

-7 to 82

20 to 70

-7 to 21

VG 68

30 to 200

-1 to 93

30 to 90

-1 to 32

VG 100

40 to 220

4 to 104

40 to 110

4 to 43

HYDRAULIC SYSTEM (PUMP)

WINCH CASE (GEAR TRAIN)

Caterpillar

Use Tractor Fluid

TDTO

TO-4

MTO

John Deere

Use Tractor Fluid

Hy-Gard

Komatsu

Use Tractor Fluid

Universal Tractor Fluid

Chevron

Use Tractor Fluid

1000 THF

Exxon-Mobil

Use Tractor Fluid

Mobil Fluid 424

Case

Use Tractor Fluid

Hy-Tran Ultra

New Holland

Use Tractor Fluid

Multitran

rienced during service so the most suitable temperature-
viscosity characteristics are obtained.

ing may have different fl uids. Note that some hydraulic
system oils are not recommended for use inside the
winch.

For inside winch housing, use the following oils:

Figure 1-5 Oil Selection Chart

Oil Capacity

The oil capacity for the H6G winch is 8.5 quarts (8 liters).

Содержание Allied H6G Series



























































































































Результаты поиска

Содержание Allied H6G Series

Отзывы:

Бренды по названию

Популярные бренды

Allied Systems Allied H6G Series, Руководство по обслуживанию

Результаты поиска

Содержание Allied H6G Series

Отзывы:

Бренды по названию

Популярные бренды