manualshive.com logo in svg

Allied Systems Allied H6G Series, Руководство по обслуживанию

Поделиться
Скачать
Allied Systems Allied H6G Series Скачать руководство пользователя страница 47

 Section 2

2 - 3

1.14 Operate lever in both directions.  Is pressure at RI & RO greater than 

the standby pilot pressure of 275±15 psi?

No

Verify that pilot pressure to direc-
tion spool PA & PB will cause the 
pump to load sense & cause pilot 
pressure to increase. Return to 
step 1.12.

Yes

Proceed to step 1.15.

1.15 Install gauges at motor ports A & B using 0-5000 psi gauges. Discon-

nect the brake line and move the lever in 

LINE-IN

 and 

LINE-OUT

. 

If pressure is below 3500 psi, is it possible to adjust the load sense 
relief valve? (Refer to Section 3 for more details on pressure check 
procedures.)

No

Replace load sense high pressure 
relief valve cartridge and return to 
step 1.12.

Yes

Adjust load sense high pressure 
relief valve to 3500 psi. Proceed 
to step 1.16.

1.16 Re-connect the brake line and put lever in 

LINE-IN

 and 

LINE-OUT

 

positions. Does winch operate?

No

Check for mechanical faults in the 
drive beyond the motor shaft.

Yes

Operate the winch.

2.

 

Winch is sluggish or erratic

2.1  Is the lever assembly in good condition? Is there air in pilot lines?

No

Repair or replace the lever assem-

bly. If there is air in the pilot lines, 
bleed them.

Yes

Proceed to step 2.2.

2.2  Is  the brake fully released?

No

Check  brake  release  circuit  or 
mechanism.  See shuttle valve 
in 2307491W  or 2307021W 
(logic control manifold) & valve 
2307622W (brake valve).

Yes

Operate the winch.

3.

 

Winch drives in one direction only.

3.1  With the control lines switched does the winch drive in opposite direc-

tion only?

No

Proceed to step 3.2.

Yes

Control signal from one side of 
joystick does not work properly.  
Repair as necessary.

3.2 With 

control lines still switched does winch drive in initial direction only? No

Proceed to step 3.3.

Yes

Problem is one side of winch direc-
tion spool.  Proceed to step 3.3.

3.3  Is there control pressure to PA & PB as well as from from RI & RO? 

Winch begins to drive when the pressure at RI or RO is 150 psi.

No

Correct control signal problem.

Yes

Operate the winch.

Содержание Allied H6G Series



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды