ALLIANCE ZWN43RSN115CW01 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 36

background image

CAUTION

If you or an unqualified person perform service on
your product, you must assume the responsibility
for any personal injury or property damage which
may result. The manufacturer will not be responsible
for any injury or property damage arising from im-
proper service and/or service procedures.

W008

NOTE: The WARNINGS and IMPORTANT INSTRUC-
TIONS appearing in this manual are not meant to cover
all possible conditions and situations that may occur.
Common sense, caution and care must be exercised
when installing, maintaining or operating the machine.

Always contact your dealer, distributor, service agent or the man-
ufacturer about any problems or conditions you do not under-
stand.

Locating an Authorized Service Person

Alliance Laundry Systems is not responsible for personal injury
or property damage resulting from improper service. Review all
service information before beginning repairs.

Warranty service must be performed by an authorized technician,
using authorized factory parts. If service is required after the war-
ranty expires, Alliance Laundry Systems also recommends con-
tacting an authorized technician and using authorized factory
parts.

Safety Information

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

6

Part No. 204666ENR1

«
...
4
5
6
7
8
...
»

Содержание ZWN43RSN115CW01





































Отзывы:

Нет отзывов

Похожие инструкции для ZWN43RSN115CW01

Бренд: Kärcher Страницы: 16

Бренд: Reaim Страницы: 12

Hydra-Clean 1235 800-268

Бренд: Graco Страницы: 24

Бренд: Kärcher Страницы: 24

Бренд: Scheppach Страницы: 36

Бренд: ZANKER Страницы: 48

Бренд: Daewoo Страницы: 50

Super 20 CL8761

Бренд: Speed Queen Страницы: 41

Бренд: Belling Страницы: 24

Бренд: Daewoo Страницы: 15

Бренд: Power Stroke Страницы: 40

Бренд: Total Страницы: 17

Бренд: Maytag Страницы: 52

Бренд: AT-OS Страницы: 60

Бренд: MAKINEX Страницы: 47

Бренд: Lavorwash Страницы: 16

Бренд: BALAY Страницы: 56

TX 300 10-130.2

Бренд: Interpump Group Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды