ALLIANCE ZWN43RSN115CW01 Скачать руководство пользователя страница 25

Страница: 25 / 36

Water Fill Does Not Stop At Proper Level

WASH, RINSE STATUS lights flash 1 or 2 times (Pressure Sensor or Fill Error), or remain on continuously (Overflow)

NOTE: The Auto Fill feature may add more water even when the Small, Medium or Large Load Sizes are selected.

Is there a Pressure

Sensor error? (WASH,

RINSE LEDs flash 1

time)

Is there an overflow

error? (WASH, RINSE

LEDs on continuously)

Check for restricted

or clogged pressure

bulb or hose. If

clear replace sensor.

Yes

Is there an air leak

in pressure hose?

Check for a leak in

the mixing valve.

Yes

Is mixing valve

inoperative?

Replace hose or

pressure bulb.

Yes

Was there a siphoning

action started in

washer causing water

to be siphoned from

washer during cycle

due to end of drain

hose being lower than

cabinet top of washer?

Test valve and

replace if

inoperative. Refer to

Mixing Valve Solenoid

Test.

Yes

Does drain hose fit

tight in standpipe or

drain?

Install 562P3 Siphon

Break Kit.

Yes

Is there water in

pressure hose?

Provide an air gap

around drain hose and

drain receptacle.

Yes

Is there broken,

loose, shorted or

incorrect wiring?

Blow air through hose

to remove water or

replace hose.

Yes

Refer to appropriate

wiring diagram.

Yes

Troubleshooting Flowcharts

DO NOT COPY or TRANSMIT

Part No. 204666ENR1

Содержание ZWN43RSN115CW01





































Результаты поиска

Содержание ZWN43RSN115CW01

Отзывы:

Похожие инструкции для ZWN43RSN115CW01

Бренды по названию

Популярные бренды

ALLIANCE ZWN43RSN115CW01, Инструкция по эксплуатации

Результаты поиска

Содержание ZWN43RSN115CW01

Отзывы:

Похожие инструкции для ZWN43RSN115CW01

Бренды по названию

Популярные бренды