Alliance Laundry Systems YT050E Скачать руководство пользователя

Страница: 29 / 61

Installation

70420301 (EN)

Basic Configuration

1. Determine the necessary conversion operations

to convert from the factory-supplied

configuration to the desired configuration.

2. Perform the conversions required so the machine

is properly configured for the desired country and

gas (refer to

Specific Conversion Procedures

section):

•

How to Convert Gas Valve from Regulated to

Unregulated

NOTE: Conversion from regulated to unregulated

is only needed when regulated tumble dryers were

ordered, but unregulated tumble dryers were

needed.

•

How to Change Burner Orifice Size

•

How to Adjust Gas Valve Governor/Regulator

3. If applicable, peel off the appropriate country

sticker (included with machine) and apply it to

the serial plate over the existing country

information.

4. If applicable, peel off the appropriate conversion

sticker (included with machine) and apply it to

the serial plate over the “ADJUSTED FOR

______ GAS: ______” information.

5. Commission tumble dryer for use.

Figure 11

Specific Conversion Procedures

How to Convert Gas Valve from Regulated to
Unregulated

NOTE: Conversion from regulated to unregulated

is only needed when regulated tumble dryers were

ordered, but unregulated tumble dryers were

needed.

1. Disconnect electrical power from tumble dryer.

Close gas shut-off valve to tumble dryer. Refer to

Figure 11

2. Follow instructions in Conversion Kit, Part No.

M400763 (Johnson Part No. Y71AA-5C).

NOTE: This kit does not contain any burner

orifices.

3. Replace burner orifice(s) as per

Table 1

4. Commission tumble dryer for use.

WARNING

When converting the tumble dryer to a

different gas or pressure, first verify that

the supply inlet pressure is equipped with

a pressure regulator (located ahead of the

tumble dryer) that will maintain the gas

supply at the inlet pressure specified.

W430R1

T103K

Gas Shut-Off Valve (Ahead of pressure tap)
(Not Supplied)

Pressure Tap

Gas Shut-Off Valve (Shown in closed
position) (Not Supplied)

SPECIFIED

LOCAL INLET

PRESSURE

Содержание YT050E






























































Результаты поиска

Содержание YT050E

Отзывы:

Похожие инструкции для YT050E

Бренды по названию

Популярные бренды

Alliance Laundry Systems YT050E, Руководство по установке

Результаты поиска

Содержание YT050E

Отзывы:

Похожие инструкции для YT050E

Бренды по названию

Популярные бренды