manualshive.com logo in svg

Alliance Laundry Systems YT050E, Руководство по установке

Поделиться
Скачать
Alliance Laundry Systems YT050E Скачать руководство пользователя страница 20

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Installation

70420301 (EN)

18

Location Requirements

The tumble dryer must be installed on a level floor. 

Floor covering materials such as carpeting or tile 

should be removed.
To assure compliance, consult local building code 

requirements. The tumble dryer must not be installed 

or stored in area where it will be exposed to water and/

or weather.

IMPORTANT: DO NOT block the airflow at the 

rear of the tumble dryer with laundry or other 

articles. Doing so would prevent adequate air 

supply to the combustion chamber of the tumble 

dryer.

A typical tumble dryer enclosure is shown in 

Figure 1

. 

Note the minimum and maximum dimensions. Local 

codes and ordinances must be complied with.

IMPORTANT: Install tumble dryers with sufficient 

clearance for servicing and operation, refer to 

Figure 1

. 

Figure 1 

WARNING

To reduce the risk of serious injury, install 

lockable door(s) to prevent public access 

to rear of tumble dryers.

W055R1

TMB2242N

NOTE: Shaded areas indicate adjacent structure.

1

0.5 in. (13 mm) recommended between machines for removal or installation

2

Allow 2-4 in. (51-102 mm) opening at top of machine to aid in removal or installation. A removable trim piece 
may be used to conceal the opening; zero clearance allowed for trim

3

4 in. (102 mm) maximum header thickness

4

12 in. (305 mm) minimum clearance permitted for remainder

5

Guard

6

Provision for make-up air

7

24 in. (610 mm) minimum, 36 in. (914 mm) recommended for maintenance purposes

8

0.25 in. (6 mm) recommended for removal or installation purposes, zero clearance allowed

TMB2242N

3

1

4

5

6

7

2

WARNING

To reduce the risk of severe injury, clearance of tumble dryer cabinet from combustible 

construction must conform to the minimum clearances.

W056R1

8

Содержание YT050E






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды