Alliance Laundry Systems YT050E страница 43 Скачать руководство пользователя

Страница: 43 / 61

Electrical Requirements

70420301 (EN)

Grounding Instructions

NOTE: To ensure protection against shock, this

tumble dryer MUST be electrically grounded in

accordance with the local codes, or in the absence

of local codes, with the latest edition of the National

Electrical Code ANSI/NFPA No. 70. In Canada the

electrical connections are to be made in accordance

with CSA C22.1 latest edition Canadian Electrical

Code, or local codes. Electrical work should be

done by a qualified electrician.

This tumble dryer must be grounded. In the event of

malfunction or breakdown, grounding will reduce the

risk of electric shock by providing a path of least

resistance for electric current. This tumble dryer must

be connected to a grounded metal, permanent wiring

system; or an equipment grounding conductor must be

run with the circuit conductors and connected to the

appropriate ground location.

•

Metal conduit and/or BX cable is not considered

ground.

•

Connecting the Neutral from the electrical

service box to the tumble dryer ground screw

does not constitute a ground.

•

A dedicated ground conduit (wire) must be

connected between the electrical service box

ground bar and tumble dryer ground screw.

For CE Models Only

All OPL (non-vend) models are factory-equipped with

an emergency stop button on the front panel.

NOTE: Activation of the emergency stop switch

stops all machine control circuit functions, but

DOES NOT remove all electrical power from

machine.

WARNING

To reduce the risk of electrical shock,

de-energize the electrical circuit being

connected to the tumble dryer before

making any electrical connections. All

electrical connections should be made by

a qualified electrician. Never attempt to

connect a live circuit.

W409R1

CAUTION

Label all wires prior to disconnection

when servicing controls. Wiring errors

can cause improper and dangerous

operation. Verify proper operation after

servicing.

W071

Содержание YT050E






























































Результаты поиска

Содержание YT050E

Отзывы:

Похожие инструкции для YT050E

Бренды по названию

Популярные бренды

Alliance Laundry Systems YT050E, Руководство по установке

Результаты поиска

Содержание YT050E

Отзывы:

Похожие инструкции для YT050E

Бренды по названию

Популярные бренды