Alliance Laundry Systems YT050E Скачать руководство пользователя

Страница: 25 / 61

Installation

70420301 (EN)

8. Place front panel on machine, loosely attach four

bottom screws. Connect door switch harness to

switch in new location. Install door assembly and

four front panel side screws loosely. Refer to

Figure 9

9. Check lint panel fit, adjusting front panel up or

down as required. Tighten four front panel side

screws to maintain position of front panel for

proper lint panel clearance.

10. Remove lint panel. Fully tighten bottom screws

on front panel.

11. Reinstall top screws and guide lugs.

12. Adjust door catch if necessary to allow

7 – 15 pounds pull (0.48 – 1.03 bar) at center of

handle.

13. Reinstall control assembly using mounting

screws.

14. Reinstall control panel and lint panel.

IMPORTANT: Restore power to tumble dryer and

test for proper operation of loading door switch.

Tumble dryer should not start with door open; an

operating tumble dryer should stop when door is

opened.

NOTE: If machine is converted back to right hand

hinge operation, the door switch harness must be

rerouted.

Figure 9

TMB1997N

Switch (New location)

Plug (New location)

Door Assembly

Side Screw

TMB1997N

Содержание YT050E






























































Результаты поиска

Содержание YT050E

Отзывы:

Похожие инструкции для YT050E

Бренды по названию

Популярные бренды

Alliance Laundry Systems YT050E, Руководство по установке

Результаты поиска

Содержание YT050E

Отзывы:

Похожие инструкции для YT050E

Бренды по названию

Популярные бренды