39201
67
Section 5 Service Procedures
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
WARNING
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
(3) Slide timer and bracket toward rear of
meter case to disengage bracket from
shoulder screw. Lift timer and bracket out
of meter case through service door opening
as far as wires will permit.
(4) Remove shoulder screw from inside meter
case.
(5) Remove two cabinet top hold down screws.
(6) Remove security bolt (if present) from left
rear corner of cabinet top.
NOTE: When lowering cabinet top into position or
reinstalling cabinet top, pivot outer tub forward far
enough to prevent damaging (bending) loading door
switch lever.
g. If area or space permits, tape loading door
closed and lift cabinet top to a vertical position
by hinging it on the rear hinges.
NOTE: Cabinet top is self supporting, however, a
small chain may be used for additional support.
Refer to Figure 38.
h. Loosen hose clamp, and disconnect filler hose
from outer tub cover. Refer to Figure 46.
NOTE: When installing filler hose, white line on
hose must point toward front of washer. Refer to
Figure 46.
i. Reach in through front of motor mounting
bracket and move idler lever to left to release
tension on belt.
IMPORTANT: Use care when releasing idler lever
tension. If idler lever spring is overstretched,
washer operation will be affected.
j. While holding idler lever, reach in and around
right side of motor and run belt off right side of
pulley.
k. Using No. 289P4 Spring Hook Tool, unhook
six module springs from lower edge of outer
tub. Refer to Figure 53.
IMPORTANT: When installing module springs,
make sure spring hook is fully seated in hole in tub
skirt.
l. Loosen hose clamp and remove drain hose from
pump outlet. Refer to Figure 53.
m. Loosen hose clamp and remove pressure hose
from pressure bulb.
n. Remove motor wire harness from support leg,
then disconnect wire harness from motor
switch by pressing down on top of connection
block and at the same time pull connection
block away from motor switch. Disconnect
wires from capacitor.
o. Grasp outer tub and lift complete tub module
assembly (with transmission and weldment
assembly attached) straight up and out of
washer cabinet.
p. Turn complete tub module upside-down and set
on protective padding.
q. Remove screw, washer and helix holding drive
pulley to input shaft and transmission
assembly. Refer to Figure 55.
r. Lift drive pulley up and off input shaft of
transmission assembly.
NOTE: When reinstalling pulley, place a small
amount of No. 03200P Lubricant on top side of the
drive pulley that will be contacting large flat
washers. Refer to Figure 55 for assembly sequence.
Lubricate helix ramps and bore with a small
amount of No. 03200P Lubricant. Refer to
Figure 56.
IMPORTANT:
DO NOT OVER LUBRICATE!
Excess lubricant can be thrown into pivot dome
area during normal washer operation. Any
lubricant on pivot dome, base or friction ring will
affect washer operation. This condition will persist
until lubricant is removed.
s. Remove screws holding three brake pads and
brake assembly to weldment assembly. Refer to
Figure 56. Then remove brake assembly and
pads off bottom of weldment assembly.
IMPORTANT: When reinstalling brake assembly,
we recommend replacing three brake pads. DO
NOT replace worn pads only. Apply a small amount
of No. 265494P Silicone Lubricant to both sides of
each brake pad where it will contact brake
assembly.
